Viewing post history: Advanced ADAPTTO controllers and compatible products

This page shows all versions of the post, starting with the most current version.
Viewing post history
This page shows all versions of the post, starting with the most current version.

Current post: Advanced ADAPTTO controllers and compatible products

Postby Adaptto E-Drives Lab » Tue Mar 18, 2014 4:27 am

We are proud to offer our MINI-E, MIDI-E and Max-E controllers for sale.



Image

Controllers' major features:
- Sine wave motor power control & intelligent adapting logics higher efficiency , less heat, silent motor operation, all sorts of protection
- Very compact for the power they are pumping through
- Display to show you everything from ride statistics and “dynamics” to voltage sag on each cell (should you opt for our BMS) and allow PC-free adjustability for you to play with the settings right on spot
- Built-in wattmeter
- Fully adjustable regen, analogue (not pre-set) regen power control given you use our throttle
- Traction control
- Cruise-control
- Possibility to set range - controller will limit the power to the necessary level
- Automatic phase/halls wires combo selection = no pain with finding the right combination just make sure the +&- of the halls are connected right the rest will be done by you but electronically through the menu on the display
- Protection motor/controller overheating – there’s a thermosensor the in controller and a thermosensor port to monitor motor’s temperature and manage the power accordingly (first the display will show you an alarm warning that you are reaching a certain temperature and once it gets to high the power will be automatically limited until the motor/controller cools down)
- Square wave, and sensorless (besides sine wave (vectored) motor control modes (if halls fail -which shouldn’t happen due to overheating protection - the controller will automatically switch to sensorless mode, so you might not even notice the halls are dead until you start on a hill)
- Automatic hibernation of the system in the time you set
- Motor and battery health monitor
- Integration with BMS – you can monitor your battery or each cell, set LVC/HVC to manage your battery’s ‘life expectancy’
- 3 fully adjustable power modes allowing you to switch between them by a push of a button and change your power settings, including regen and speed limits
- Auxiliary devices connection bus to enable BMS or DC-DC converter control through the display
- The throttle control the power, not the speed of the motor(however you can switch it to speed control if you like)

1) We've decreased the prices by more than 10%!

2) For retail orders please contact one of our exclusive distributors: http://adaptto.envolt.se/ and http://vectorebike.com/

3) We accept CC payments!


Here are the specs:
Image

!!!Please note: the controller cannot be used with Crystalyte Crown motor!!!


Every controller kit contains the controller itself, connectors and display:

Image

Also you can order BMS board which is compatible with our controllers and is fully adjustable using from the controller display.

You will also get a discount when purchasing complete kit MINI-E+BMS

Here is how the latest bms version looks like (28s)
Image

you can see 7 aux boards with individual 4s connectors grouped in 4 + 1+ 1+ 1 so minimal configuration is 4 boards up to 16cells and max config is 7 boards, up to 28cells.
Each board can be configured for 2-4 cells.

BRAND NEW WIRING SCHEME IS NOW AVAILABLE!

Image

You can find large interactive scheme here: http://adaptto.com/Support/

Please do not hesitate to contact us via PM or via email sales@adaptto.ru
Edited by Adaptto E-Drives Lab on Tue May 31, 2016 5:22 am.
For sales enquiries please contact us via: sales@adaptto.com
Technical questions: techsupport@adaptto.com
Web-site: http://adaptto.com/
User avatar
Adaptto E-Drives Lab
100 W
100 W
 
Posts: 119
Joined: Fri Mar 02, 2012 5:01 pm
Location: Moscow, Russia

Revision 23: Advanced ADAPTTO controllers and compatible products

Postby Adaptto E-Drives Lab » Tue Mar 18, 2014 4:27 am

We are proud to offer our MINI-E, MIDI-E and Max-E controllers for sale.

Image

Image

Controllers' major features:
- Sine wave motor power control & intelligent adapting logics higher efficiency , less heat, silent motor operation, all sorts of protection
- Very compact for the power they are pumping through
- Display to show you everything from ride statistics and “dynamics” to voltage sag on each cell (should you opt for our BMS) and allow PC-free adjustability for you to play with the settings right on spot
- Built-in wattmeter
- Fully adjustable regen, analogue (not pre-set) regen power control given you use our throttle
- Traction control
- Cruise-control
- Possibility to set range - controller will limit the power to the necessary level
- Automatic phase/halls wires combo selection = no pain with finding the right combination just make sure the +&- of the halls are connected right the rest will be done by you but electronically through the menu on the display
- Protection motor/controller overheating – there’s a thermosensor the in controller and a thermosensor port to monitor motor’s temperature and manage the power accordingly (first the display will show you an alarm warning that you are reaching a certain temperature and once it gets to high the power will be automatically limited until the motor/controller cools down)
- Square wave, and sensorless (besides sine wave (vectored) motor control modes (if halls fail -which shouldn’t happen due to overheating protection - the controller will automatically switch to sensorless mode, so you might not even notice the halls are dead until you start on a hill)
- Automatic hibernation of the system in the time you set
- Motor and battery health monitor
- Integration with BMS – you can monitor your battery or each cell, set LVC/HVC to manage your battery’s ‘life expectancy’
- 3 fully adjustable power modes allowing you to switch between them by a push of a button and change your power settings, including regen and speed limits
- Auxiliary devices connection bus to enable BMS or DC-DC converter control through the display
- The throttle control the power, not the speed of the motor(however you can switch it to speed control if you like)

1) We've decreased the prices by more than 10%!

2) For retail orders please contact our exclusive distributor: http://adaptto.envolt.se/

3) PayPal is now being accepted!


Here are the specs:
Image

!!!Please note: the controller cannot be used with Crystalyte Crown motor!!!


Every controller kit contains the controller itself, connectors and display:

Image

Also you can order BMS board which is compatible with our controllers and is fully adjustable using from the controller display.

You will also get a discount when purchasing complete kit MINI-E+BMS

Here is how the latest bms version looks like (28s)
Image

you can see 7 aux boards with individual 4s connectors grouped in 4 + 1+ 1+ 1 so minimal configuration is 4 boards up to 16cells and max config is 7 boards, up to 28cells.
Each board can be configured for 2-4 cells.
[size=150][color=#0000FF]

BRAND NEW WIRING SCHEME IS NOW AVAILABLE!

Image

You can find large interactive scheme here: http://adaptto.com/Support/

Please do not hesitate to contact us via PM or via email sales@adaptto.ru
Edited by Adaptto E-Drives Lab on Thu Dec 10, 2015 9:17 am.
For sales enquiries please contact us via: sales@adaptto.com
Technical questions: techsupport@adaptto.com
Web-site: http://adaptto.com/
User avatar
Adaptto E-Drives Lab
100 W
100 W
 
Posts: 119
Joined: Fri Mar 02, 2012 5:01 pm
Location: Moscow, Russia

Revision 22: Advanced ADAPTTO controllers and compatible products

Postby Adaptto E-Drives Lab » Tue Mar 18, 2014 4:27 am

We are proud to offer our MINI-E, MIDI-E and Max-E controllers for sale.

Image

Controllers' major features:
- Sine wave motor power control & intelligent adapting logics higher efficiency , less heat, silent motor operation, all sorts of protection
- Very compact for the power they are pumping through
- Display to show you everything from ride statistics and “dynamics” to voltage sag on each cell (should you opt for our BMS) and allow PC-free adjustability for you to play with the settings right on spot
- Built-in wattmeter
- Fully adjustable regen, analogue (not pre-set) regen power control given you use our throttle
- Traction control
- Cruise-control
- Possibility to set range - controller will limit the power to the necessary level
- Automatic phase/halls wires combo selection = no pain with finding the right combination just make sure the +&- of the halls are connected right the rest will be done by you but electronically through the menu on the display
- Protection motor/controller overheating – there’s a thermosensor the in controller and a thermosensor port to monitor motor’s temperature and manage the power accordingly (first the display will show you an alarm warning that you are reaching a certain temperature and once it gets to high the power will be automatically limited until the motor/controller cools down)
- Square wave, and sensorless (besides sine wave (vectored) motor control modes (if halls fail -which shouldn’t happen due to overheating protection - the controller will automatically switch to sensorless mode, so you might not even notice the halls are dead until you start on a hill)
- Automatic hibernation of the system in the time you set
- Motor and battery health monitor
- Integration with BMS – you can monitor your battery or each cell, set LVC/HVC to manage your battery’s ‘life expectancy’
- 3 fully adjustable power modes allowing you to switch between them by a push of a button and change your power settings, including regen and speed limits
- Auxiliary devices connection bus to enable BMS or DC-DC converter control through the display
- The throttle control the power, not the speed of the motor(however you can switch it to speed control if you like)

1) We've decreased the prices by more than 10%!

2) For retail orders please contact our exclusive distributor: http://adaptto.envolt.se/

3) PayPal is now being accepted!


Here are the specs:
Image

!!!Please note: the controller cannot be used with Crystalyte Crown motor!!!


Every controller kit contains the controller itself, connectors and display:

Image

Also you can order BMS board which is compatible with our controllers and is fully adjustable using from the controller display.

You will also get a discount when purchasing complete kit MINI-E+BMS

Here is how the latest bms version looks like (28s)
Image

you can see 7 aux boards with individual 4s connectors grouped in 4 + 1+ 1+ 1 so minimal configuration is 4 boards up to 16cells and max config is 7 boards, up to 28cells.
Each board can be configured for 2-4 cells.
[size=150][color=#0000FF]

BRAND NEW WIRING SCHEME IS NOW AVAILABLE!

Image

You can find large interactive scheme here: http://adaptto.com/Support/

Please do not hesitate to contact us via PM or via email sales@adaptto.ru
Edited by Adaptto E-Drives Lab on Mon Dec 07, 2015 1:54 am.
For sales enquiries please contact us via: sales@adaptto.com
Technical questions: techsupport@adaptto.com
Web-site: http://adaptto.com/
User avatar
Adaptto E-Drives Lab
100 W
100 W
 
Posts: 119
Joined: Fri Mar 02, 2012 5:01 pm
Location: Moscow, Russia

Revision 21: Advanced ADAPTTO controllers/10%+ discounts/PayPal accepted

Postby Adaptto E-Drives Lab » Tue Mar 18, 2014 4:27 am

We are proud to offer our MINI-E, MIDI-E and Max-E controllers for sale.

Image

Controllers' major features:
- Sine wave motor power control & intelligent adapting logics higher efficiency , less heat, silent motor operation, all sorts of protection
- Very compact for the power they are pumping through
- Display to show you everything from ride statistics and “dynamics” to voltage sag on each cell (should you opt for our BMS) and allow PC-free adjustability for you to play with the settings right on spot
- Built-in wattmeter
- Fully adjustable regen, analogue (not pre-set) regen power control given you use our throttle
- Traction control
- Cruise-control
- Possibility to set range - controller will limit the power to the necessary level
- Automatic phase/halls wires combo selection = no pain with finding the right combination just make sure the +&- of the halls are connected right the rest will be done by you but electronically through the menu on the display
- Protection motor/controller overheating – there’s a thermosensor the in controller and a thermosensor port to monitor motor’s temperature and manage the power accordingly (first the display will show you an alarm warning that you are reaching a certain temperature and once it gets to high the power will be automatically limited until the motor/controller cools down)
- Square wave, and sensorless (besides sine wave (vectored) motor control modes (if halls fail -which shouldn’t happen due to overheating protection - the controller will automatically switch to sensorless mode, so you might not even notice the halls are dead until you start on a hill)
- Automatic hibernation of the system in the time you set
- Motor and battery health monitor
- Integration with BMS – you can monitor your battery or each cell, set LVC/HVC to manage your battery’s ‘life expectancy’
- 3 fully adjustable power modes allowing you to switch between them by a push of a button and change your power settings, including regen and speed limits
- Auxiliary devices connection bus to enable BMS or DC-DC converter control through the display
- The throttle control the power, not the speed of the motor(however you can switch it to speed control if you like)

1) We've decreased the prices by more than 10%!

2) For retail orders please contact our exclusive distributor: http://adaptto.envolt.se/

3) PayPal is now being accepted!


Here are the specs:
Image

!!!Please note: the controller cannot be used with Crystalyte Crown motor!!!


Every controller kit contains the controller itself, connectors and display:

Image

Also you can order BMS board which is compatible with our controllers and is fully adjustable using from the controller display.

You will also get a discount when purchasing complete kit MINI-E+BMS

Here is how the latest bms version looks like (28s)
Image

you can see 7 aux boards with individual 4s connectors grouped in 4 + 1+ 1+ 1 so minimal configuration is 4 boards up to 16cells and max config is 7 boards, up to 28cells.
Each board can be configured for 2-4 cells.
[size=150][color=#0000FF]

BRAND NEW WIRING SCHEME IS NOW AVAILABLE!

Image

You can find large interactive scheme here: http://adaptto.com/Support/

Please do not hesitate to contact us via PM or via email sales@adaptto.ru
Edited by Adaptto E-Drives Lab on Tue Nov 03, 2015 4:23 am.
For sales enquiries please contact us via: sales@adaptto.com
Technical questions: techsupport@adaptto.com
Web-site: http://adaptto.com/
User avatar
Adaptto E-Drives Lab
100 W
100 W
 
Posts: 119
Joined: Fri Mar 02, 2012 5:01 pm
Location: Moscow, Russia

Revision 20: Advanced ADAPTTO controllers/10%+ discounts/PayPal accepted

Postby Adaptto E-Drives Lab » Tue Mar 18, 2014 4:27 am

We are proud to offer our MINI-E and Max-E controllers for sale.

Image Image

Controllers' major features:
- Sine wave motor power control & intelligent adapting logics higher efficiency , less heat, silent motor operation, all sorts of protection
- Very compact for the power they are pumping through
- Display to show you everything from ride statistics and “dynamics” to voltage sag on each cell (should you opt for our BMS) and allow PC-free adjustability for you to play with the settings right on spot
- Built-in wattmeter
- Fully adjustable regen, analogue (not pre-set) regen power control given you use our throttle
- Traction control
- Cruise-control
- Possibility to set range - controller will limit the power to the necessary level
- Automatic phase/halls wires combo selection = no pain with finding the right combination just make sure the +&- of the halls are connected right the rest will be done by you but electronically through the menu on the display
- Protection motor/controller overheating – there’s a thermosensor the in controller and a thermosensor port to monitor motor’s temperature and manage the power accordingly (first the display will show you an alarm warning that you are reaching a certain temperature and once it gets to high the power will be automatically limited until the motor/controller cools down)
- Square wave, and sensorless (besides sine wave (vectored) motor control modes (if halls fail -which shouldn’t happen due to overheating protection - the controller will automatically switch to sensorless mode, so you might not even notice the halls are dead until you start on a hill)
- Automatic hibernation of the system in the time you set
- Motor and battery health monitor
- Integration with BMS – you can monitor your battery or each cell, set LVC/HVC to manage your battery’s ‘life expectancy’
- 3 fully adjustable power modes allowing you to switch between them by a push of a button and change your power settings, including regen and speed limits
- Auxiliary devices connection bus to enable BMS or DC-DC converter control through the display
- The throttle control the power, not the speed of the motor(however you can switch it to speed control if you like)

1) We've decreased the prices by more than 10%!

2) For retail orders please contact our exclusive distributor: http://adaptto.envolt.se/

3) PayPal is now being accepted!


Here are the specs:
Image

!!!Please note: the controller cannot be used with Crystalyte Crown motor!!!


Every controller kit contains the controller itself, connectors and display:

Image

Also you can order BMS board which is compatible with our controllers and is fully adjustable using from the controller display.

You will also get a discount when purchasing complete kit MINI-E+BMS

Here is how the latest bms version looks like (28s)
Image

you can see 7 aux boards with individual 4s connectors grouped in 4 + 1+ 1+ 1 so minimal configuration is 4 boards up to 16cells and max config is 7 boards, up to 28cells.
Each board can be configured for 2-4 cells.
[size=150][color=#0000FF]

BRAND NEW WIRING SCHEME IS NOW AVAILABLE!

Image

You can find large interactive scheme here: http://adaptto.com/Support/

Please do not hesitate to contact us via PM or via email sales@adaptto.ru
Edited by Adaptto E-Drives Lab on Wed Sep 30, 2015 3:37 am.
For sales enquiries please contact us via: sales@adaptto.com
Technical questions: techsupport@adaptto.com
Web-site: http://adaptto.com/
User avatar
Adaptto E-Drives Lab
100 W
100 W
 
Posts: 119
Joined: Fri Mar 02, 2012 5:01 pm
Location: Moscow, Russia

Revision 19: Advanced ADAPTTO controllers/10%+ discounts/PayPal accepted

Postby Adaptto E-Drives Lab » Tue Mar 18, 2014 4:27 am

We are proud to offer our MINI-E and Max-E controllers for sale.

Image Image

Controllers' major features:
- Sine wave motor power control & intelligent adapting logics higher efficiency , less heat, silent motor operation, all sorts of protection
- Very compact for the power they are pumping through
- Display to show you everything from ride statistics and “dynamics” to voltage sag on each cell (should you opt for our BMS) and allow PC-free adjustability for you to play with the settings right on spot
- Built-in wattmeter
- Fully adjustable regen, analogue (not pre-set) regen power control given you use our throttle
- Traction control
- Cruise-control
- Possibility to set range - controller will limit the power to the necessary level
- Automatic phase/halls wires combo selection = no pain with finding the right combination just make sure the +&- of the halls are connected right the rest will be done by you but electronically through the menu on the display
- Protection motor/controller overheating – there’s a thermosensor the in controller and a thermosensor port to monitor motor’s temperature and manage the power accordingly (first the display will show you an alarm warning that you are reaching a certain temperature and once it gets to high the power will be automatically limited until the motor/controller cools down)
- Square wave, and sensorless (besides sine wave (vectored) motor control modes (if halls fail -which shouldn’t happen due to overheating protection - the controller will automatically switch to sensorless mode, so you might not even notice the halls are dead until you start on a hill)
- Automatic hibernation of the system in the time you set
- Motor and battery health monitor
- Integration with BMS – you can monitor your battery or each cell, set LVC/HVC to manage your battery’s ‘life expectancy’
- 3 fully adjustable power modes allowing you to switch between them by a push of a button and change your power settings, including regen and speed limits
- Auxiliary devices connection bus to enable BMS or DC-DC converter control through the display
- The throttle control the power, not the speed of the motor(however you can switch it to speed control if you like)

1) We've decreased the prices by more than 10%!

2) For retail orders please contact our exclusive distributor: http://adaptto.envolt.se/

3) PayPal is now being accepted!


Here are the specs:
Image

!!!Please note: the controller cannot be used with Crystalyte Crown motor!!!


Every controller kit contains the controller itself, connectors and display:

Image

Also you can order BMS board which is compatible with our controllers and is fully adjustable using from the controller display.

You will also get a discount when purchasing complete kit MINI-E+BMS

Here is how the latest bms version looks like (28s)
Image

you can see 7 aux boards with individual 4s connectors grouped in 4 + 1+ 1+ 1 so minimal configuration is 4 boards up to 16cells and max config is 7 boards, up to 28cells.
Each board can be configured for 2-4 cells.
[size=150][color=#0000FF]

BRAND NEW WIRING SCHEME IS NOW AVAILABLE!

Image

You can find large interactive scheme here: http://adaptto.com/Support/

Please do not hesitate to contact us via PM or via email sales@adaptto.ru
Edited by Adaptto E-Drives Lab on Tue Sep 29, 2015 8:05 am.
For sales enquiries please contact us via: sales@adaptto.com
Technical questions: techsupport@adaptto.com
Web-site: http://adaptto.com/
User avatar
Adaptto E-Drives Lab
100 W
100 W
 
Posts: 119
Joined: Fri Mar 02, 2012 5:01 pm
Location: Moscow, Russia

Revision 18: Advanced ADAPTTO controllers/10%+ discounts/PayPal accepted

Postby Adaptto E-Drives Lab » Tue Mar 18, 2014 4:27 am

We are proud to offer our MINI-E and Max-E controllers for sale.

Image Image

Controllers' major features:
- Sine wave motor power control & intelligent adapting logics higher efficiency , less heat, silent motor operation, all sorts of protection
- Very compact for the power they are pumping through
- Display to show you everything from ride statistics and “dynamics” to voltage sag on each cell (should you opt for our BMS) and allow PC-free adjustability for you to play with the settings right on spot
- Built-in wattmeter
- Fully adjustable regen, analogue (not pre-set) regen power control given you use our throttle
- Traction control
- Cruise-control
- Possibility to set range - controller will limit the power to the necessary level
- Automatic phase/halls wires combo selection = no pain with finding the right combination just make sure the +&- of the halls are connected right the rest will be done by you but electronically through the menu on the display
- Protection motor/controller overheating – there’s a thermosensor the in controller and a thermosensor port to monitor motor’s temperature and manage the power accordingly (first the display will show you an alarm warning that you are reaching a certain temperature and once it gets to high the power will be automatically limited until the motor/controller cools down)
- Square wave, and sensorless (besides sine wave (vectored) motor control modes (if halls fail -which shouldn’t happen due to overheating protection - the controller will automatically switch to sensorless mode, so you might not even notice the halls are dead until you start on a hill)
- Automatic hibernation of the system in the time you set
- Motor and battery health monitor
- Integration with BMS – you can monitor your battery or each cell, set LVC/HVC to manage your battery’s ‘life expectancy’
- 3 fully adjustable power modes allowing you to switch between them by a push of a button and change your power settings, including regen and speed limits
- Auxiliary devices connection bus to enable BMS or DC-DC converter control through the display
- The throttle control the power, not the speed of the motor(however you can switch it to speed control if you like)

1) We've decreased the prices by more than 10%!

2) For retail orders please contact our exclusive distributor: http://adaptto.envolt.se/

3) PayPal is now being accepted!


Here are the specs:
Image

!!!Please note: the controller cannot be used with Crystalyte Crown motor!!!


Every controller kit contains the controller itself, connectors and display:

Image

Also you can order BMS board which is compatible with our controllers and is fully adjustable using from the controller display.

You will also get a discount when purchasing complete kit MINI-E+BMS

Here is how the latest bms version looks like (28s)
Image

you can see 7 aux boards with individual 4s connectors grouped in 4 + 1+ 1+ 1 so minimal configuration is 4 boards up to 16cells and max config is 7 boards, up to 28cells.
Each board can be configured for 2-4 cells.
[size=150][color=#0000FF]

BRAND NEW WIRING SCHEME IS NOW AVAILABLE!

Image

You can find large interactive scheme here: http://adaptto.com/Support/

Please do not hesitate to contact us via PM or via email sales@adaptto.ru
Edited by Adaptto E-Drives Lab on Tue Sep 29, 2015 6:15 am.
For sales enquiries please contact us via: sales@adaptto.com
Technical questions: techsupport@adaptto.com
Web-site: http://adaptto.com/
User avatar
Adaptto E-Drives Lab
100 W
100 W
 
Posts: 119
Joined: Fri Mar 02, 2012 5:01 pm
Location: Moscow, Russia

Revision 17: Advanced ADAPTTO controllers/10%+ discounts/PayPal accepted

Postby Adaptto E-Drives Lab » Tue Mar 18, 2014 4:27 am

We are proud to offer our MINI-E and Max-E controllers for sale.

Image Image

Controllers' major features:
- Sine wave motor power control & intelligent adapting logics higher efficiency , less heat, silent motor operation, all sorts of protection
- Very compact for the power they are pumping through
- Display to show you everything from ride statistics and “dynamics” to voltage sag on each cell (should you opt for our BMS) and allow PC-free adjustability for you to play with the settings right on spot
- Built-in wattmeter
- Fully adjustable regen, analogue (not pre-set) regen power control given you use our throttle
- Traction control
- Cruise-control
- Possibility to set range - controller will limit the power to the necessary level
- Automatic phase/halls wires combo selection = no pain with finding the right combination just make sure the +&- of the halls are connected right the rest will be done by you but electronically through the menu on the display
- Protection motor/controller overheating – there’s a thermosensor the in controller and a thermosensor port to monitor motor’s temperature and manage the power accordingly (first the display will show you an alarm warning that you are reaching a certain temperature and once it gets to high the power will be automatically limited until the motor/controller cools down)
- Square wave, and sensorless (besides sine wave (vectored) motor control modes (if halls fail -which shouldn’t happen due to overheating protection - the controller will automatically switch to sensorless mode, so you might not even notice the halls are dead until you start on a hill)
- Automatic hibernation of the system in the time you set
- Motor and battery health monitor
- Integration with BMS – you can monitor your battery or each cell, set LVC/HVC to manage your battery’s ‘life expectancy’
- 3 fully adjustable power modes allowing you to switch between them by a push of a button and change your power settings, including regen and speed limits
- Auxiliary devices connection bus to enable BMS or DC-DC converter control through the display
- The throttle control the power, not the speed of the motor(however you can switch it to speed control if you like)

1) We've decreased the prices by more than 10%!

2) For retail orders please contact our exclusive distributor: http://adaptto.envolt.se/

3) PayPal is now being accepted!


Here are the specs:
Image

!!!Please note: the controller cannot be used with Crystalyte Crown motor!!!


Every controller kit contains the controller itself, connectors and display:

Image

Also you can order BMS board which is compatible with our controllers and is fully adjustable using from the controller display.

You will also get a discount when purchasing complete kit MINI-E+BMS

Here is how the latest bms version looks like (28s)
Image

you can see 7 aux boards with individual 4s connectors grouped in 4 + 1+ 1+ 1 so minimal configuration is 4 boards up to 16cells and max config is 7 boards, up to 28cells.
Each board can be configured for 2-4 cells.
[size=150][color=#0000FF]

BRAND NEW WIRING SCHEME IS NOW AVAILABLE!

Image

You can find large interactive scheme here: http://adaptto.com/Support/

Please do not hesitate to contact us via PM or via email sales@adaptto.ru
Edited by Adaptto E-Drives Lab on Tue Sep 29, 2015 5:49 am.
For sales enquiries please contact us via: sales@adaptto.com
Technical questions: techsupport@adaptto.com
Web-site: http://adaptto.com/
User avatar
Adaptto E-Drives Lab
100 W
100 W
 
Posts: 119
Joined: Fri Mar 02, 2012 5:01 pm
Location: Moscow, Russia

Revision 16: Advanced ADAPTTO controllers/10%+ discounts/PayPal accepted

Postby Adaptto E-Drives Lab » Tue Mar 18, 2014 4:27 am

We are proud to offer our MINI-E and Max-E controllers for sale.

Image Image

Controllers' major features:
- Sine wave motor power control & intelligent adapting logics higher efficiency , less heat, silent motor operation, all sorts of protection
- Very compact for the power they are pumping through
- Display to show you everything from ride statistics and “dynamics” to voltage sag on each cell (should you opt for our BMS) and allow PC-free adjustability for you to play with the settings right on spot
- Built-in wattmeter
- Fully adjustable regen, analogue (not pre-set) regen power control given you use our throttle
- Traction control
- Cruise-control
- Possibility to set range - controller will limit the power to the necessary level
- Automatic phase/halls wires combo selection = no pain with finding the right combination just make sure the +&- of the halls are connected right the rest will be done by you but electronically through the menu on the display
- Protection motor/controller overheating – there’s a thermosensor the in controller and a thermosensor port to monitor motor’s temperature and manage the power accordingly (first the display will show you an alarm warning that you are reaching a certain temperature and once it gets to high the power will be automatically limited until the motor/controller cools down)
- Square wave, and sensorless (besides sine wave (vectored) motor control modes (if halls fail -which shouldn’t happen due to overheating protection - the controller will automatically switch to sensorless mode, so you might not even notice the halls are dead until you start on a hill)
- Automatic hibernation of the system in the time you set
- Motor and battery health monitor
- Integration with BMS – you can monitor your battery or each cell, set LVC/HVC to manage your battery’s ‘life expectancy’
- 3 fully adjustable power modes allowing you to switch between them by a push of a button and change your power settings, including regen and speed limits
- Auxiliary devices connection bus to enable BMS or DC-DC converter control through the display
- The throttle control the power, not the speed of the motor(however you can switch it to speed control if you like)

1) We've decreased the prices by more than 10%!

2) For retail orders please contact our exclusive distributor: http://adaptto.envolt.se/

3) PayPal is now being accepted!


Here are the specs:
Image

!!!Please note: the controller cannot be used with Crystalyte Crown motor!!!


Every controller kit contains the controller itself, connectors and display:

Image

Also you can order BMS board which is compatible with our controllers and is fully adjustable using from the controller display.

You will also get a discount when purchasing complete kit MINI-E+BMS

Here is how the latest bms version looks like (28s)
Image

you can see 7 aux boards with individual 4s connectors grouped in 4 + 1+ 1+ 1 so minimal configuration is 4 boards up to 16cells and max config is 7 boards, up to 28cells.
Each board can be configured for 2-4 cells.
[size=150][color=#0000FF]


Please do not hesitate to contact us via PM or via email sales@adaptto.ru


Image
Edited by Adaptto E-Drives Lab on Mon Sep 07, 2015 8:51 am.
For sales enquiries please contact us via: sales@adaptto.com
Technical questions: techsupport@adaptto.com
Web-site: http://adaptto.com/
User avatar
Adaptto E-Drives Lab
100 W
100 W
 
Posts: 119
Joined: Fri Mar 02, 2012 5:01 pm
Location: Moscow, Russia

Revision 15: Advanced ADAPTTO controllers/10%+ discounts/PayPal accepted

Postby Adaptto E-Drives Lab » Tue Mar 18, 2014 4:27 am

We are proud to offer our MINI-E and Max-E controllers for sale.

Image Image

Controllers' major features:
- Sine wave motor power control & intelligent adapting logics higher efficiency , less heat, silent motor operation, all sorts of protection
- Very compact for the power they are pumping through
- Display to show you everything from ride statistics and “dynamics” to voltage sag on each cell (should you opt for our BMS) and allow PC-free adjustability for you to play with the settings right on spot
- Built-in wattmeter
- Fully adjustable regen, analogue (not pre-set) regen power control given you use our throttle
- Traction control
- Cruise-control
- Possibility to set range - controller will limit the power to the necessary level
- Automatic phase/halls wires combo selection = no pain with finding the right combination just make sure the +&- of the halls are connected right the rest will be done by you but electronically through the menu on the display
- Protection motor/controller overheating – there’s a thermosensor the in controller and a thermosensor port to monitor motor’s temperature and manage the power accordingly (first the display will show you an alarm warning that you are reaching a certain temperature and once it gets to high the power will be automatically limited until the motor/controller cools down)
- Square wave, and sensorless (besides sine wave (vectored) motor control modes (if halls fail -which shouldn’t happen due to overheating protection - the controller will automatically switch to sensorless mode, so you might not even notice the halls are dead until you start on a hill)
- Automatic hibernation of the system in the time you set
- Motor and battery health monitor
- Integration with BMS – you can monitor your battery or each cell, set LVC/HVC to manage your battery’s ‘life expectancy’
- 3 fully adjustable power modes allowing you to switch between them by a push of a button and change your power settings, including regen and speed limits
- Auxiliary devices connection bus to enable BMS or DC-DC converter control through the display
- The throttle control the power, not the speed of the motor(however you can switch it to speed control if you like)

1) We've decreased the prices by more than 10%!

2) For retail orders please contact our exclusive distributor: http://adaptto.envolt.se/

3) PayPal is now being accepted!


Here are the specs:
Image

!!!Please note: the controller cannot be used with Crystalyte Crown motor!!!


Every controller kit contains the controller itself, connectors and display:

Image

Also you can order BMS board which is compatible with our controllers and is fully adjustable using from the controller display.

You will also get a discount when purchasing complete kit MINI-E+BMS

Here is how the latest bms version looks like (28s)
Image

you can see 7 aux boards with individual 4s connectors grouped in 4 + 1+ 1+ 1 so minimal configuration is 4 boards up to 16cells and max config is 7 boards, up to 28cells.
Each board can be configured for 2-4 cells.
[size=150][color=#0000FF]


Please do not hesitate to contact us via PM or via email sales@adaptto.ru
Edited by Adaptto E-Drives Lab on Thu Jul 30, 2015 6:21 am.
For sales enquiries please contact us via: sales@adaptto.com
Technical questions: techsupport@adaptto.com
Web-site: http://adaptto.com/
User avatar
Adaptto E-Drives Lab
100 W
100 W
 
Posts: 119
Joined: Fri Mar 02, 2012 5:01 pm
Location: Moscow, Russia

Revision 14: Advanced ADAPTTO controllers and BMS boards

Postby Adaptto E-Drives Lab » Tue Mar 18, 2014 4:27 am

We are proud to offer our MINI-E and Max-E controllers for sale.

Image Image

Controllers' major features:
- Sine wave motor power control & intelligent adapting logics higher efficiency , less heat, silent motor operation, all sorts of protection
- Very compact for the power they are pumping through
- Display to show you everything from ride statistics and “dynamics” to voltage sag on each cell (should you opt for our BMS) and allow PC-free adjustability for you to play with the settings right on spot
- Built-in wattmeter
- Fully adjustable regen, analogue (not pre-set) regen power control given you use our throttle
- Traction control
- Cruise-control
- Possibility to set range - controller will limit the power to the necessary level
- Automatic phase/halls wires combo selection = no pain with finding the right combination just make sure the +&- of the halls are connected right the rest will be done by you but electronically through the menu on the display
- Protection motor/controller overheating – there’s a thermosensor the in controller and a thermosensor port to monitor motor’s temperature and manage the power accordingly (first the display will show you an alarm warning that you are reaching a certain temperature and once it gets to high the power will be automatically limited until the motor/controller cools down)
- Square wave, and sensorless (besides sine wave (vectored) motor control modes (if halls fail -which shouldn’t happen due to overheating protection - the controller will automatically switch to sensorless mode, so you might not even notice the halls are dead until you start on a hill)
- Automatic hibernation of the system in the time you set
- Motor and battery health monitor
- Integration with BMS – you can monitor your battery or each cell, set LVC/HVC to manage your battery’s ‘life expectancy’
- 3 fully adjustable power modes allowing you to switch between them by a push of a button and change your power settings, including regen and speed limits
- Auxiliary devices connection bus to enable BMS or DC-DC converter control through the display
- The throttle control the power, not the speed of the motor(however you can switch it to speed control if you like)

1) We've decreased the prices by more than 10%!

2) For retail orders please contact our exclusive distributor: http://adaptto.envolt.se/

3) PayPal is now being accepted!


Here are the specs:
Image

!!!Please note: the controller cannot be used with Crystalyte Crown motor!!!


Every controller kit contains the controller itself, connectors and display:

Image

Also you can order BMS board which is compatible with our controllers and is fully adjustable using from the controller display.

You will also get a discount when purchasing complete kit MINI-E+BMS

Here is how the latest bms version looks like (28s)
Image

you can see 7 aux boards with individual 4s connectors grouped in 4 + 1+ 1+ 1 so minimal configuration is 4 boards up to 16cells and max config is 7 boards, up to 28cells.
Each board can be configured for 2-4 cells.
[size=150][color=#0000FF]


Please do not hesitate to contact us via PM or via email sales@adaptto.ru
Edited by Adaptto E-Drives Lab on Thu Jul 30, 2015 4:06 am.
For sales enquiries please contact us via: sales@adaptto.com
Technical questions: techsupport@adaptto.com
Web-site: http://adaptto.com/
User avatar
Adaptto E-Drives Lab
100 W
100 W
 
Posts: 119
Joined: Fri Mar 02, 2012 5:01 pm
Location: Moscow, Russia

Revision 13: Advanced ADAPTTO controllers and BMS boards

Postby Adaptto E-Drives Lab » Tue Mar 18, 2014 4:27 am

We are proud to offer our MINI-E and Max-E controllers for sale.

Image Image

Controllers' major features:
- Sine wave motor power control & intelligent adapting logics higher efficiency , less heat, silent motor operation, all sorts of protection
- Very compact for the power they are pumping through
- Display to show you everything from ride statistics and “dynamics” to voltage sag on each cell (should you opt for our BMS) and allow PC-free adjustability for you to play with the settings right on spot
- Built-in wattmeter
- Fully adjustable regen, analogue (not pre-set) regen power control given you use our throttle
- Traction control
- Cruise-control
- Possibility to set range - controller will limit the power to the necessary level
- Automatic phase/halls wires combo selection = no pain with finding the right combination just make sure the +&- of the halls are connected right the rest will be done by you but electronically through the menu on the display
- Protection motor/controller overheating – there’s a thermosensor the in controller and a thermosensor port to monitor motor’s temperature and manage the power accordingly (first the display will show you an alarm warning that you are reaching a certain temperature and once it gets to high the power will be automatically limited until the motor/controller cools down)
- Square wave, and sensorless (besides sine wave (vectored) motor control modes (if halls fail -which shouldn’t happen due to overheating protection - the controller will automatically switch to sensorless mode, so you might not even notice the halls are dead until you start on a hill)
- Automatic hibernation of the system in the time you set
- Motor and battery health monitor
- Integration with BMS – you can monitor your battery or each cell, set LVC/HVC to manage your battery’s ‘life expectancy’
- 3 fully adjustable power modes allowing you to switch between them by a push of a button and change your power settings, including regen and speed limits
- Auxiliary devices connection bus to enable BMS or DC-DC converter control through the display
- The throttle control the power, not the speed of the motor(however you can switch it to speed control if you like)

OUR CONTROLLERS SUPPORT PAS SENSOR (optional +20 USD to the price) - please contact us beforehand to include this option into controller order

Here are the specs:
Image

!!!Please note: the controller cannot be used with Crystalite Crown motor!!!


Every controller kit contains the controller itself, connectors and display:

Image

Also you can order BMS board which is compatible with our controllers and is fully adjustable using from the controller display.

You will also get a discount when purchasing complete kit MINI-E+BMS

Here is how the latest bms version looks like (28s)
Image

you can see 7 aux boards with individual 4s connectors grouped in 4 + 1+ 1+ 1 so minimal configuration is 4 boards up to 16cells and max config is 7 boards, up to 28cells.
Each board can be configured for 2-4 cells.
[size=150][color=#0000FF]


Please do not hesitate to contact us via PM or via email sales@adaptto.ru
Edited by Adaptto E-Drives Lab on Fri Jun 05, 2015 2:39 am.
For sales enquiries please contact us via: sales@adaptto.com
Technical questions: techsupport@adaptto.com
Web-site: http://adaptto.com/
User avatar
Adaptto E-Drives Lab
100 W
100 W
 
Posts: 119
Joined: Fri Mar 02, 2012 5:01 pm
Location: Moscow, Russia

Revision 12: Advanced ADAPTTO controllers and BMS boards

Postby Adaptto E-Drives Lab » Tue Mar 18, 2014 4:27 am

We are proud to offer our MINI-E and Max-E controllers for sale.

Image Image

Controllers' major features:
- Sine wave motor power control & intelligent adapting logics higher efficiency , less heat, silent motor operation, all sorts of protection
- Very compact for the power they are pumping through
- Display to show you everything from ride statistics and “dynamics” to voltage sag on each cell (should you opt for our BMS) and allow PC-free adjustability for you to play with the settings right on spot
- Built-in wattmeter
- Fully adjustable regen, analogue (not pre-set) regen power control given you use our throttle
- Traction control
- Cruise-control
- Possibility to set range - controller will limit the power to the necessary level
- Automatic phase/halls wires combo selection = no pain with finding the right combination just make sure the +&- of the halls are connected right the rest will be done by you but electronically through the menu on the display
- Protection motor/controller overheating – there’s a thermosensor the in controller and a thermosensor port to monitor motor’s temperature and manage the power accordingly (first the display will show you an alarm warning that you are reaching a certain temperature and once it gets to high the power will be automatically limited until the motor/controller cools down)
- Square wave, and sensorless (besides sine wave (vectored) motor control modes (if halls fail -which shouldn’t happen due to overheating protection - the controller will automatically switch to sensorless mode, so you might not even notice the halls are dead until you start on a hill)
- Automatic hibernation of the system in the time you set
- Motor and battery health monitor
- Integration with BMS – you can monitor your battery or each cell, set LVC/HVC to manage your battery’s ‘life expectancy’
- 3 fully adjustable power modes allowing you to switch between them by a push of a button and change your power settings, including regen and speed limits
- Auxiliary devices connection bus to enable BMS or DC-DC converter control through the display
- The throttle control the power, not the speed of the motor(however you can switch it to speed control if you like)

OUR CONTROLLERS SUPPORT PAS SENSOR (optional +20 USD to the price) - please contact us beforehand to include this option into controller order

Here are the specs:
Image

!!!Please note: the controller cannot be used with Crystalite Crown motor!!!


Every controller kit contains the controller itself, connectors and display:

Image

Also you can order BMS board which is compatible with our controllers and is fully adjustable using from the controller display.

You will also get a discount when purchasing complete kit MINI-E+BMS

Here is how the latest bms version looks like (28s)
Image

you can see 7 aux boards with individual 4s connectors grouped in 4 + 1+ 1+ 1 so minimal configuration is 4 boards up to 16cells and max config is 7 boards, up to 28cells.
Each board can be configured for 2-4 cells.

DEAR FRIENDS!

TIME TO START A NEW BUILD! :D

IN APRIL ONLY - WHOLESALE PRICES FOR RETAIL ORDERS!


Image

Please do not hesitate to contact us via PM or via email sales@adaptto.ru
Edited by Adaptto E-Drives Lab on Mon Jun 01, 2015 4:11 am.
For sales enquiries please contact us via: sales@adaptto.com
Technical questions: techsupport@adaptto.com
Web-site: http://adaptto.com/
User avatar
Adaptto E-Drives Lab
100 W
100 W
 
Posts: 119
Joined: Fri Mar 02, 2012 5:01 pm
Location: Moscow, Russia

Revision 11: FREE SHIPPING in May for ADAPTTO controllers and BMS boards

Postby Adaptto E-Drives Lab » Tue Mar 18, 2014 4:27 am

We are proud to offer our MINI-E and Max-E controllers for sale.

Image Image

Controllers' major features:
- Sine wave motor power control & intelligent adapting logics higher efficiency , less heat, silent motor operation, all sorts of protection
- Very compact for the power they are pumping through
- Display to show you everything from ride statistics and “dynamics” to voltage sag on each cell (should you opt for our BMS) and allow PC-free adjustability for you to play with the settings right on spot
- Built-in wattmeter
- Fully adjustable regen, analogue (not pre-set) regen power control given you use our throttle
- Traction control
- Cruise-control
- Possibility to set range - controller will limit the power to the necessary level
- Automatic phase/halls wires combo selection = no pain with finding the right combination just make sure the +&- of the halls are connected right the rest will be done by you but electronically through the menu on the display
- Protection motor/controller overheating – there’s a thermosensor the in controller and a thermosensor port to monitor motor’s temperature and manage the power accordingly (first the display will show you an alarm warning that you are reaching a certain temperature and once it gets to high the power will be automatically limited until the motor/controller cools down)
- Square wave, and sensorless (besides sine wave (vectored) motor control modes (if halls fail -which shouldn’t happen due to overheating protection - the controller will automatically switch to sensorless mode, so you might not even notice the halls are dead until you start on a hill)
- Automatic hibernation of the system in the time you set
- Motor and battery health monitor
- Integration with BMS – you can monitor your battery or each cell, set LVC/HVC to manage your battery’s ‘life expectancy’
- 3 fully adjustable power modes allowing you to switch between them by a push of a button and change your power settings, including regen and speed limits
- Auxiliary devices connection bus to enable BMS or DC-DC converter control through the display
- The throttle control the power, not the speed of the motor(however you can switch it to speed control if you like)

OUR CONTROLLERS SUPPORT PAS SENSOR (optional +20 USD to the price) - please contact us beforehand to include this option into controller order

Here are the specs:
Image

!!!Please note: the controller cannot be used with Crystalite Crown motor!!!


Every controller kit contains the controller itself, connectors and display:

Image

Also you can order BMS board which is compatible with our controllers and is fully adjustable using from the controller display.

You will also get a discount when purchasing complete kit MINI-E+BMS

Here is how the latest bms version looks like (28s)
Image

you can see 7 aux boards with individual 4s connectors grouped in 4 + 1+ 1+ 1 so minimal configuration is 4 boards up to 16cells and max config is 7 boards, up to 28cells.
Each board can be configured for 2-4 cells.

DEAR FRIENDS!

TIME TO START A NEW BUILD! :D

IN APRIL ONLY - WHOLESALE PRICES FOR RETAIL ORDERS!


Image

Please do not hesitate to contact us via PM or via email sales@adaptto.ru
Edited by Adaptto E-Drives Lab on Wed May 13, 2015 7:44 am.
For sales enquiries please contact us via: sales@adaptto.com
Technical questions: techsupport@adaptto.com
Web-site: http://adaptto.com/
User avatar
Adaptto E-Drives Lab
100 W
100 W
 
Posts: 119
Joined: Fri Mar 02, 2012 5:01 pm
Location: Moscow, Russia

Revision 10: SPECIAL OFFERS for ADAPTTO controllers and BMS boards

Postby Adaptto E-Drives Lab » Tue Mar 18, 2014 4:27 am

We are proud to offer our MINI-E and Max-E controllers for sale.

Image Image

Controllers' major features:
- Sine wave motor power control & intelligent adapting logics higher efficiency , less heat, silent motor operation, all sorts of protection
- Very compact for the power they are pumping through
- Display to show you everything from ride statistics and “dynamics” to voltage sag on each cell (should you opt for our BMS) and allow PC-free adjustability for you to play with the settings right on spot
- Built-in wattmeter
- Fully adjustable regen, analogue (not pre-set) regen power control given you use our throttle
- Traction control
- Cruise-control
- Possibility to set range - controller will limit the power to the necessary level
- Automatic phase/halls wires combo selection = no pain with finding the right combination just make sure the +&- of the halls are connected right the rest will be done by you but electronically through the menu on the display
- Protection motor/controller overheating – there’s a thermosensor the in controller and a thermosensor port to monitor motor’s temperature and manage the power accordingly (first the display will show you an alarm warning that you are reaching a certain temperature and once it gets to high the power will be automatically limited until the motor/controller cools down)
- Square wave, and sensorless (besides sine wave (vectored) motor control modes (if halls fail -which shouldn’t happen due to overheating protection - the controller will automatically switch to sensorless mode, so you might not even notice the halls are dead until you start on a hill)
- Automatic hibernation of the system in the time you set
- Motor and battery health monitor
- Integration with BMS – you can monitor your battery or each cell, set LVC/HVC to manage your battery’s ‘life expectancy’
- 3 fully adjustable power modes allowing you to switch between them by a push of a button and change your power settings, including regen and speed limits
- Auxiliary devices connection bus to enable BMS or DC-DC converter control through the display
- The throttle control the power, not the speed of the motor(however you can switch it to speed control if you like)

OUR CONTROLLERS SUPPORT PAS SENSOR (optional +20 USD to the price) - please contact us beforehand to include this option into controller order

Here are the specs:
Image

!!!Please note: the controller cannot be used with Crystalite Crown motor!!!


Every controller kit contains the controller itself, connectors and display:

Image

Also you can order BMS board which is compatible with our controllers and is fully adjustable using from the controller display.

You will also get a discount when purchasing complete kit MINI-E+BMS

Here is how the latest bms version looks like (28s)
Image

you can see 7 aux boards with individual 4s connectors grouped in 4 + 1+ 1+ 1 so minimal configuration is 4 boards up to 16cells and max config is 7 boards, up to 28cells.
Each board can be configured for 2-4 cells.

DEAR FRIENDS!

TIME TO START A NEW BUILD! :D

IN APRIL ONLY - WHOLESALE PRICES FOR RETAIL ORDERS!


Image

Please do not hesitate to contact us via PM or via email sales@adaptto.ru
Edited by Adaptto E-Drives Lab on Thu Apr 02, 2015 7:51 am.
For sales enquiries please contact us via: sales@adaptto.com
Technical questions: techsupport@adaptto.com
Web-site: http://adaptto.com/
User avatar
Adaptto E-Drives Lab
100 W
100 W
 
Posts: 119
Joined: Fri Mar 02, 2012 5:01 pm
Location: Moscow, Russia

Revision 9: The most advanced Adaptto Mini-E and Max-E Controllers + BMS

Postby Adaptto E-Drives Lab » Tue Mar 18, 2014 4:27 am

We are proud to offer our MINI-E and Max-E controllers for sale.

Image Image

Controllers' major features:
- Sine wave motor power control & intelligent adapting logics higher efficiency , less heat, silent motor operation, all sorts of protection
- Very compact for the power they are pumping through
- Display to show you everything from ride statistics and “dynamics” to voltage sag on each cell (should you opt for our BMS) and allow PC-free adjustability for you to play with the settings right on spot
- Built-in wattmeter
- Fully adjustable regen, analogue (not pre-set) regen power control given you use our throttle
- Traction control
- Cruise-control
- Possibility to set range - controller will limit the power to the necessary level
- Automatic phase/halls wires combo selection = no pain with finding the right combination just make sure the +&- of the halls are connected right the rest will be done by you but electronically through the menu on the display
- Protection motor/controller overheating – there’s a thermosensor the in controller and a thermosensor port to monitor motor’s temperature and manage the power accordingly (first the display will show you an alarm warning that you are reaching a certain temperature and once it gets to high the power will be automatically limited until the motor/controller cools down)
- Square wave, and sensorless (besides sine wave (vectored) motor control modes (if halls fail -which shouldn’t happen due to overheating protection - the controller will automatically switch to sensorless mode, so you might not even notice the halls are dead until you start on a hill)
- Automatic hibernation of the system in the time you set
- Motor and battery health monitor
- Integration with BMS – you can monitor your battery or each cell, set LVC/HVC to manage your battery’s ‘life expectancy’
- 3 fully adjustable power modes allowing you to switch between them by a push of a button and change your power settings, including regen and speed limits
- Auxiliary devices connection bus to enable BMS or DC-DC converter control through the display
- The throttle control the power, not the speed of the motor(however you can switch it to speed control if you like)

OUR CONTROLLERS SUPPORT PAS SENSOR (optional +20 USD to the price) - please contact us beforehand to include this option into controller order

Here are the specs:
Image

!!!Please note: the controller cannot be used with Crystalite Crown motor!!!


The cost of Mini-E is 435usd + SH = on stock.

The cost of MAX-E is 760USD + SH = on stock.

Every controller kit contains the controller itself, connectors and display:

Image

Also you can order BMS board which is compatible with our controllers and is fully adjustable using from the controller display.
The price for BMS is:
16s and less: 120usd
28s 150usd
each additional 4s board would cost 13usd


You will also get a discount when purchasing complete kit MINI-E+BMS

Here is how the latest bms version looks like (28s)
Image

you can see 7 aux boards with individual 4s connectors grouped in 4 + 1+ 1+ 1 so minimal configuration is 4 boards up to 16cells and max config is 7 boards, up to 28cells.
Each board can be configured for 2-4 cells.

Please do not hesitate to contact us via PM or via email sales@adaptto.ru
Edited by Adaptto E-Drives Lab on Wed Mar 11, 2015 9:49 am.
For sales enquiries please contact us via: sales@adaptto.com
Technical questions: techsupport@adaptto.com
Web-site: http://adaptto.com/
User avatar
Adaptto E-Drives Lab
100 W
100 W
 
Posts: 119
Joined: Fri Mar 02, 2012 5:01 pm
Location: Moscow, Russia

Revision 8: The most advanced Adaptto Mini-E and Max-E Controllers + BMS

Postby Adaptto E-Drives Lab » Tue Mar 18, 2014 4:27 am

We are proud to offer our MINI-E and Max-E controllers for sale.

Image Image

Controllers' major features:
- Sine wave motor power control & intelligent adapting logics higher efficiency , less heat, silent motor operation, all sorts of protection
- Very compact for the power they are pumping through
- Display to show you everything from ride statistics and “dynamics” to voltage sag on each cell (should you opt for our BMS) and allow PC-free adjustability for you to play with the settings right on spot
- Built-in wattmeter
- Fully adjustable regen, analogue (not pre-set) regen power control given you use our throttle
- Traction control
- Cruise-control
- Possibility to set range - controller will limit the power to the necessary level
- Automatic phase/halls wires combo selection = no pain with finding the right combination just make sure the +&- of the halls are connected right the rest will be done by you but electronically through the menu on the display
- Protection motor/controller overheating – there’s a thermosensor the in controller and a thermosensor port to monitor motor’s temperature and manage the power accordingly (first the display will show you an alarm warning that you are reaching a certain temperature and once it gets to high the power will be automatically limited until the motor/controller cools down)
- Square wave, and sensorless (besides sine wave (vectored) motor control modes (if halls fail -which shouldn’t happen due to overheating protection - the controller will automatically switch to sensorless mode, so you might not even notice the halls are dead until you start on a hill)
- Automatic hibernation of the system in the time you set
- Motor and battery health monitor
- Integration with BMS – you can monitor your battery or each cell, set LVC/HVC to manage your battery’s ‘life expectancy’
- 3 fully adjustable power modes allowing you to switch between them by a push of a button and change your power settings, including regen and speed limits
- Auxiliary devices connection bus to enable BMS or DC-DC converter control through the display
- The throttle control the power, not the speed of the motor(however you can switch it to speed control if you like)

Here are the specs:
Image

!!!Please note: the controller cannot be used with Crystalite Crown motor!!!


[u]WE HAVE DECREASED ALL OUR PRICES BY 5%! CHECK THIS OUT ON OUR NEW WEB-SITE: http://adaptto.com/[/u]
The cost of Mini-E is 435usd + SH = on stock.

The cost of MAX-E is 760USD + SH = on stock.

Every controller kit contains the controller itself, connectors and display:

Image

Also you can order BMS board which is compatible with our controllers and is fully adjustable using from the controller display.
The price for BMS is:
16s and less: 120usd
28s 150usd
each additional 4s board would cost 13usd


You will also get a discount when purchasing complete kit MINI-E+BMS

Here is how the latest bms version looks like (28s)
Image

you can see 7 aux boards with individual 4s connectors grouped in 4 + 1+ 1+ 1 so minimal configuration is 4 boards up to 16cells and max config is 7 boards, up to 28cells.
Each board can be configured for 2-4 cells.

Please do not hesitate to contact us via PM or via email sales@adaptto.ru

[u]WE HAVE DECREASED ALL OUR PRICES BY 5%! CHECK THIS OUT ON OUR NEW WEB-SITE: http://adaptto.com/[/u]
Edited by Adaptto E-Drives Lab on Thu Feb 19, 2015 9:53 am.
For sales enquiries please contact us via: sales@adaptto.com
Technical questions: techsupport@adaptto.com
Web-site: http://adaptto.com/
User avatar
Adaptto E-Drives Lab
100 W
100 W
 
Posts: 119
Joined: Fri Mar 02, 2012 5:01 pm
Location: Moscow, Russia

Revision 7: The most advanced Adaptto Mini-E and Max-E Controllers + BMS

Postby Adaptto E-Drives Lab » Tue Mar 18, 2014 4:27 am

We are proud to offer our MINI-E and Max-E controllers for sale.

Image Image

Controllers have the following features:
Controllers major features:
- Sine wave motor power control & intelligent adapting logics higher efficiency , less heat, silent motor operation, all sorts of protection
- Very compact for the power they are pumping through
- Display to show you everything from ride statistics and “dynamics” to voltage sag on each cell (should you opt for our BMS) and allow PC-free adjustability for you to play with the settings right on spot
- Built-in wattmeter
- Fully adjustable regen, analogue (not pre-set) regen power control given you use our throttle
- Traction control
- Cruise-control
- Possibility to set range - controller will limit the power to the necessary level
- Automatic phase/halls wires combo selection = no pain with finding the right combination just make sure the +&- of the halls are connected right the rest will be done by you but electronically through the menu on the display
- Protection motor/controller overheating – there’s a thermosensor the in controller and a thermosensor port to monitor motor’s temperature and manage the power accordingly (first the display will show you an alarm warning that you are reaching a certain temperature and once it gets to high the power will be automatically limited until the motor/controller cools down)
- Square wave, and sensorless (besides sine wave (vectored) motor control modes (if halls fail -which shouldn’t happen due to overheating protection - the controller will automatically switch to sensorless mode, so you might not even notice the halls are dead until you start on a hill)
- Automatic hibernation of the system in the time you set
- Motor and battery health monitor
- Integration with BMS – you can monitor your battery or each cell, set LVC/HVC to manage your battery’s ‘life expectancy’
- 3 fully adjustable power modes allowing you to switch between them by a push of a button and change your power settings, including regen and speed limits
- Auxiliary devices connection bus to enable BMS or DC-DC converter control through the display
- The throttle control the power, not the speed of the motor(however you can switch it to speed control if you like)

Here are the specs:
Image

!!!Please note: the controller cannot be used with Crystalite Crown motor!!!


[u]WE HAVE DECREASED ALL OUR PRICES BY 5%! CHECK THIS OUT ON OUR NEW WEB-SITE: http://adaptto.com/[/u]
The cost of Mini-E is 435usd + SH = on stock.

The cost of MAX-E is 760USD + SH = on stock.

Every controller kit contains the controller itself, connectors and display:

Image

Also you can order BMS board which is compatible with our controllers and is fully adjustable using from the controller display.
The price for BMS is:
16s and less: 120usd
28s 150usd
each additional 4s board would cost 13usd


You will also get a discount when purchasing complete kit MINI-E+BMS

Here is how the latest bms version looks like (28s)
Image

you can see 7 aux boards with individual 4s connectors grouped in 4 + 1+ 1+ 1 so minimal configuration is 4 boards up to 16cells and max config is 7 boards, up to 28cells.
Each board can be configured for 2-4 cells.

Please do not hesitate to contact us via PM or via email sales@adaptto.ru

[u]WE HAVE DECREASED ALL OUR PRICES BY 5%! CHECK THIS OUT ON OUR NEW WEB-SITE: http://adaptto.com/[/u]
Edited by Adaptto E-Drives Lab on Wed Feb 04, 2015 10:00 am.
For sales enquiries please contact us via: sales@adaptto.com
Technical questions: techsupport@adaptto.com
Web-site: http://adaptto.com/
User avatar
Adaptto E-Drives Lab
100 W
100 W
 
Posts: 119
Joined: Fri Mar 02, 2012 5:01 pm
Location: Moscow, Russia

Revision 6: The most advanced Adaptto Mini-E and Max-E Controllers + BMS

Postby Adaptto E-Drives Lab » Tue Mar 18, 2014 4:27 am

We are proud to offer our MINI-E and Max-E controllers for sale.

Image Image

Controllers have the following features:
Controllers major features:
- Sine wave motor power control & intelligent adapting logics higher efficiency , less heat, silent motor operation, all sorts of protection
- Very compact for the power they are pumping through
- Display to show you everything from ride statistics and “dynamics” to voltage sag on each cell (should you opt for our BMS) and allow PC-free adjustability for you to play with the settings right on spot
- Built-in wattmeter
- Fully adjustable regen, analogue (not pre-set) regen power control given you use our throttle
- Traction control
- Cruise-control
- Possibility to set range - controller will limit the power to the necessary level
- Automatic phase/halls wires combo selection = no pain with finding the right combination just make sure the +&- of the halls are connected right the rest will be done by you but electronically through the menu on the display
- Protection motor/controller overheating – there’s a thermosensor the in controller and a thermosensor port to monitor motor’s temperature and manage the power accordingly (first the display will show you an alarm warning that you are reaching a certain temperature and once it gets to high the power will be automatically limited until the motor/controller cools down)
- Square wave, and sensorless (besides sine wave (vectored) motor control modes (if halls fail -which shouldn’t happen due to overheating protection - the controller will automatically switch to sensorless mode, so you might not even notice the halls are dead until you start on a hill)
- Automatic hibernation of the system in the time you set
- Motor and battery health monitor
- Integration with BMS – you can monitor your battery or each cell, set LVC/HVC to manage your battery’s ‘life expectancy’
- 3 fully adjustable power modes allowing you to switch between them by a push of a button and change your power settings, including regen and speed limits
- Auxiliary devices connection bus to enable BMS or DC-DC converter control through the display
- The throttle control the power, not the speed of the motor(however you can switch it to speed control if you like)

Here are the specs:
Image

[u]WE HAVE DECREASED ALL OUR PRICES BY 5%! CHECK THIS OUT ON OUR NEW WEB-SITE: http://adaptto.com/[/u]
The cost of Mini-E is 435usd + SH = on stock.

The cost of MAX-E is 760USD + SH = on stock.

Every controller kit contains the controller itself, connectors and display:

Image

Also you can order BMS board which is compatible with our controllers and is fully adjustable using from the controller display.
The price for BMS is:
16s and less: 120usd
28s 150usd
each additional 4s board would cost 13usd


You will also get a discount when purchasing complete kit MINI-E+BMS

Here is how the latest bms version looks like (28s)
Image

you can see 7 aux boards with individual 4s connectors grouped in 4 + 1+ 1+ 1 so minimal configuration is 4 boards up to 16cells and max config is 7 boards, up to 28cells.
Each board can be configured for 2-4 cells.

Please do not hesitate to contact us via PM or via email sales@adaptto.ru

[u]WE HAVE DECREASED ALL OUR PRICES BY 5%! CHECK THIS OUT ON OUR NEW WEB-SITE: http://adaptto.com/[/u]
Edited by Adaptto E-Drives Lab on Mon Jan 19, 2015 8:45 am.
For sales enquiries please contact us via: sales@adaptto.com
Technical questions: techsupport@adaptto.com
Web-site: http://adaptto.com/
User avatar
Adaptto E-Drives Lab
100 W
100 W
 
Posts: 119
Joined: Fri Mar 02, 2012 5:01 pm
Location: Moscow, Russia

Revision 5: The most advanced Adaptto Mini-E and Max-E Controllers + BMS

Postby Adaptto E-Drives Lab » Tue Mar 18, 2014 4:27 am

We are proud to offer our MINI-E and Max-E controllers for sale.

Image Image

Controllers have the following features:
Controllers major features:
- Sine wave motor power control & intelligent adapting logics higher efficiency , less heat, silent motor operation, all sorts of protection
- Very compact for the power they are pumping through
- Display to show you everything from ride statistics and “dynamics” to voltage sag on each cell (should you opt for our BMS) and allow PC-free adjustability for you to play with the settings right on spot
- Built-in wattmeter
- Fully adjustable regen, analogue (not pre-set) regen power control given you use our throttle
- Traction control
- Cruise-control
- Possibility to set range - controller will limit the power to the necessary level
- Automatic phase/halls wires combo selection = no pain with finding the right combination just make sure the +&- of the halls are connected right the rest will be done by you but electronically through the menu on the display
- Protection motor/controller overheating – there’s a thermosensor the in controller and a thermosensor port to monitor motor’s temperature and manage the power accordingly (first the display will show you an alarm warning that you are reaching a certain temperature and once it gets to high the power will be automatically limited until the motor/controller cools down)
- Square wave, and sensorless (besides sine wave (vectored) motor control modes (if halls fail -which shouldn’t happen due to overheating protection - the controller will automatically switch to sensorless mode, so you might not even notice the halls are dead until you start on a hill)
- Automatic hibernation of the system in the time you set
- Motor and battery health monitor
- Integration with BMS – you can monitor your battery or each cell, set LVC/HVC to manage your battery’s ‘life expectancy’
- 3 fully adjustable power modes allowing you to switch between them by a push of a button and change your power settings, including regen and speed limits
- Auxiliary devices connection bus to enable BMS or DC-DC converter control through the display
- The throttle control the power, not the speed of the motor(however you can switch it to speed control if you like)

Here are the specs:
Image

[u]WE HAVE DECREASED ALL OUR PRICES BY 5%! CHECK THIS OUT ON OUR NEW WEB-SITE: http://adaptto.com/[/u]
The cost of Mini-E is 435usd + SH = on stock.

The cost of MAX-E is 760USD + SH = on stock.

Every controller kit contains the controller itself, connectors and display:

Image

Also you can order BMS board which is compatible with our controllers and is fully adjustable using from the controller display.
The price for BMS is:
16s and less: 120usd
28s 150usd
each additional 4s board would cost 13usd


You will also get a discount when purchasing complete kit MINI-E+BMS

Here is how the latest bms version looks like (28s)
Image

you can see 7 aux boards with individual 4s connectors grouped in 4 + 1+ 1+ 1 so minimal configuration is 4 boards up to 16cells and max config is 7 boards, up to 28cells.
Each board can be configured for 2-4 cells.

Please do not hesitate to contact us via PM or via email sales@adaptto.ru

[u]WE HAVE DECREASED ALL OUR PRICES BY 5%! CHECK THIS OUT ON OUR NEW WEB-SITE: http://adaptto.com/[/u]
Edited by Adaptto E-Drives Lab on Fri Jan 16, 2015 10:00 am.
For sales enquiries please contact us via: sales@adaptto.com
Technical questions: techsupport@adaptto.com
Web-site: http://adaptto.com/
User avatar
Adaptto E-Drives Lab
100 W
100 W
 
Posts: 119
Joined: Fri Mar 02, 2012 5:01 pm
Location: Moscow, Russia

Revision 4: The most advanced Adaptto Mini-E and Max-E Controllers + BMS

Postby Adaptto E-Drives Lab » Tue Mar 18, 2014 4:27 am

We are proud to offer our MINI-E and Max-E controllers for sale.

Image Image

Controllers have the following features:
Controllers major features:
- Sine wave motor power control & intelligent adapting logics higher efficiency , less heat, silent motor operation, all sorts of protection
- Very compact for the power they are pumping through
- Display to show you everything from ride statistics and “dynamics” to voltage sag on each cell (should you opt for our BMS) and allow PC-free adjustability for you to play with the settings right on spot
- Built-in wattmeter
- Fully adjustable regen, analogue (not pre-set) regen power control given you use our throttle
- Traction control
- Cruise-control
- Possibility to set range - controller will limit the power to the necessary level
- Automatic phase/halls wires combo selection = no pain with finding the right combination just make sure the +&- of the halls are connected right the rest will be done by you but electronically through the menu on the display
- Protection motor/controller overheating – there’s a thermosensor the in controller and a thermosensor port to monitor motor’s temperature and manage the power accordingly (first the display will show you an alarm warning that you are reaching a certain temperature and once it gets to high the power will be automatically limited until the motor/controller cools down)
- Square wave, and sensorless (besides sine wave (vectored) motor control modes (if halls fail -which shouldn’t happen due to overheating protection - the controller will automatically switch to sensorless mode, so you might not even notice the halls are dead until you start on a hill)
- Automatic hibernation of the system in the time you set
- Motor and battery health monitor
- Integration with BMS – you can monitor your battery or each cell, set LVC/HVC to manage your battery’s ‘life expectancy’
- 3 fully adjustable power modes allowing you to switch between them by a push of a button and change your power settings, including regen and speed limits
- Auxiliary devices connection bus to enable BMS or DC-DC converter control through the display
- The throttle control the power, not the speed of the motor(however you can switch it to speed control if you like)

Here are the specs:
Image

[u]WE HAVE DECREASED ALL OUR PRICES BY 5%! CHECK THIS OUT ON OUR NEW WEB-SITE: http://adaptto.com/[/u]
The cost of Mini-E is 435usd + SH = on stock.

The cost of MAX-E is 760USD + SH = on stock.
Also you can order BMS board which is compatible with our controllers and is fully adjustable using from the controller display.
The price for BMS is:

16s and less: 120usd
28s 150usd
each additional 4s board would cost 13usd

You will also get a discount when purchasing complete kit MINI-E+BMS

Here is how the latest bms version looks like (28s)
Image

you can see 7 aux boards with individual 4s connectors grouped in 4 + 1+ 1+ 1 so minimal configuration is 4 boards up to 16cells and max config is 7 boards, up to 28cells.
Each board can be configured for 2-4 cells.

Please do not hesitate to contact us via PM or via email sales@adaptto.ru

[u]WE HAVE DECREASED ALL OUR PRICES BY 5%! CHECK THIS OUT ON OUR NEW WEB-SITE: http://adaptto.com/[/u]
Edited by Adaptto E-Drives Lab on Fri Jan 16, 2015 9:42 am.
For sales enquiries please contact us via: sales@adaptto.com
Technical questions: techsupport@adaptto.com
Web-site: http://adaptto.com/
User avatar
Adaptto E-Drives Lab
100 W
100 W
 
Posts: 119
Joined: Fri Mar 02, 2012 5:01 pm
Location: Moscow, Russia

Revision 3: The most advanced Adaptto Mini-E Controller + BMS

Postby Adaptto E-Drives Lab » Tue Mar 18, 2014 4:27 am

We are proud to offer our MINI-E controllers for sale.

Image

Controllers the following features:
Controllers major features:
- Sine wave motor power control & intelligent adapting logics higher efficiency , less heat, silent motor operation, all sorts of protection
- Very compact for the power they are pumping through
- Display to show you everything from ride statistics and “dynamics” to voltage sag on each cell (should you opt for our BMS) and allow PC-free adjustability for you to play with the settings right on spot
- Built-in wattmeter
- Fully adjustable regen, analogue (not pre-set) regen power control given you use our throttle
- Traction control
- Cruise-control
- Possibility to set range - controller will limit the power to the necessary level
- Automatic phase/halls wires combo selection = no pain with finding the right combination just make sure the +&- of the halls are connected right the rest will be done by you but electronically through the menu on the display
- Protection motor/controller overheating – there’s a thermosensor the in controller and a thermosensor port to monitor motor’s temperature and manage the power accordingly (first the display will show you an alarm warning that you are reaching a certain temperature and once it gets to high the power will be automatically limited until the motor/controller cools down)
- Square wave, and sensorless (besides sine wave (vectored) motor control modes (if halls fail -which shouldn’t happen due to overheating protection - the controller will automatically switch to sensorless mode, so you might not even notice the halls are dead until you start on a hill)
- Automatic hibernation of the system in the time you set
- Motor and battery health monitor
- Integration with BMS – you can monitor your battery or each cell, set LVC/HVC to manage your battery’s ‘life expectancy’
- 3 fully adjustable power modes allowing you to switch between them by a push of a button and change your power settings, including regen and speed limits
- Auxiliary devices connection bus to enable BMS or DC-DC converter control through the display
- The throttle control the power, not the speed of the motor(however you can switch it to speed control if you like)

Here is the specs:
Image

The cost of Mini-E is 450usd + SH = on stock.

The cost of MAX-E is 800USD + SH = they are on preorder right now, not available for sale at the moment.

Also you can order BMS board which is compatible with our controllers and is fully adjustable using from the controller display.
The price for BMS is:

16s and less: 125usd
28s 155usd
each additional 4s board would cost 13usd

You will also get a discount when purchasing complete kit MINI-E+BMS

Here is how the latest bms version looks like (28s)
Image

you can see 7 aux boards with individual 4s connectors grouped in 4 + 1+ 1+ 1 so minimal configuration is 4 boards up to 16cells and max config is 7 boards, up to 28cells.
Each board can be configured for 2-4 cells.

Please do not hesitate to contact us via PM or via email sales@adaptto.ru
Edited by Adaptto E-Drives Lab on Mon Apr 07, 2014 8:23 am.
For sales enquiries please contact us via: sales@adaptto.com
Technical questions: techsupport@adaptto.com
Web-site: http://adaptto.com/
User avatar
Adaptto E-Drives Lab
100 W
100 W
 
Posts: 119
Joined: Fri Mar 02, 2012 5:01 pm
Location: Moscow, Russia

Revision 2: The most advanced Adaptto Mini-E Controller + BMS

Postby Adaptto E-Drives Lab » Tue Mar 18, 2014 4:27 am

We are proud to offer our MINI-E controllers for sale.

Image

Controllers the following features:
Controllers major features:
- Sine wave motor power control & intelligent adapting logics higher efficiency , less heat, silent motor operation, all sorts of protection
- Very compact for the power they are pumping through
- Display to show you everything from ride statistics and “dynamics” to voltage sag on each cell (should you opt for our BMS) and allow PC-free adjustability for you to play with the settings right on spot
- Built-in wattmeter
- Fully adjustable regen, analogue (not pre-set) regen power control given you use our throttle
- Traction control
- Cruise-control
- Possibility to set range - controller will limit the power to the necessary level
- Automatic phase/halls wires combo selection = no pain with finding the right combination just make sure the +&- of the halls are connected right the rest will be done by you but electronically through the menu on the display
- Protection motor/controller overheating – there’s a thermosensor the in controller and a thermosensor port to monitor motor’s temperature and manage the power accordingly (first the display will show you an alarm warning that you are reaching a certain temperature and once it gets to high the power will be automatically limited until the motor/controller cools down)
- Square wave, and sensorless (besides sine wave (vectored) motor control modes (if halls fail -which shouldn’t happen due to overheating protection - the controller will automatically switch to sensorless mode, so you might not even notice the halls are dead until you start on a hill)
- Automatic hibernation of the system in the time you set
- Motor and battery health monitor
- Integration with BMS – you can monitor your battery or each cell, set LVC/HVC to manage your battery’s ‘life expectancy’
- 3 fully adjustable power modes allowing you to switch between them by a push of a button and change your power settings, including regen and speed limits
- Auxiliary devices connection bus to enable BMS or DC-DC converter control through the display
- The throttle control the power, not the speed of the motor(however you can switch it to speed control if you like)

Here is the specs:
Image

The cost of Mini-E is 450usd + SH = on stock.

The cost of MAX-E is 800USD + SH = they are on preorder right now, not available for sale at the moment.

Also you can order BMS board which is compatible with our controllers and is fully adjustable using from the controller display.
The price for BMS is:

16s and less: 125usd
28s 155usd
each additional 4s board would cost 13usd

You will also get a discount when purchasing complete kit MINI-E+BMS

Here is how the latest bms version looks like (28s)
Image

you can see 7 aux boards with individual 4s connectors grouped in 4 + 1+ 1+ 1 so minimal configuration is 4 boards up to 16cells and max config is 7 boards, up to 28cells.
Each board can be configured for 2-4 cells.

Please do not hesitate to contact us via PM or via email sales@adaptto.ru
Edited by Adaptto E-Drives Lab on Fri Mar 21, 2014 7:42 am.
For sales enquiries please contact us via: sales@adaptto.com
Technical questions: techsupport@adaptto.com
Web-site: http://adaptto.com/
User avatar
Adaptto E-Drives Lab
100 W
100 W
 
Posts: 119
Joined: Fri Mar 02, 2012 5:01 pm
Location: Moscow, Russia

Revision 1: The most advanced Adaptto Mini-E Controller + BMS

Postby Adaptto E-Drives Lab » Tue Mar 18, 2014 4:27 am

We are proud to offer our MINI-E controllers for sale.

Image

Controllers the following features:
Controllers major features:
- Sine wave motor power control & intelligent adapting logics higher efficiency , less heat, silent motor operation, all sorts of protection
- Very compact for the power they are pumping through
- Display to show you everything from ride statistics and “dynamics” to voltage sag on each cell (should you opt for our BMS) and allow PC-free adjustability for you to play with the settings right on spot
- Built-in wattmeter
- Fully adjustable regen, analogue (not pre-set) regen power control given you use our throttle
- Traction control
- Cruise-control
- Possibility to set range - controller will limit the power to the necessary level
- Automatic phase/halls wires combo selection = no pain with finding the right combination just make sure the +&- of the halls are connected right the rest will be done by you but electronically through the menu on the display
- Protection motor/controller overheating – there’s a thermosensor the in controller and a thermosensor port to monitor motor’s temperature and manage the power accordingly (first the display will show you an alarm warning that you are reaching a certain temperature and once it gets to high the power will be automatically limited until the motor/controller cools down)
- Square wave, and sensorless (besides sine wave (vectored) motor control modes (if halls fail -which shouldn’t happen due to overheating protection - the controller will automatically switch to sensorless mode, so you might not even notice the halls are dead until you start on a hill)
- Automatic hibernation of the system in the time you set
- Motor and battery health monitor
- Integration with BMS – you can monitor your battery or each cell, set LVC/HVC to manage your battery’s ‘life expectancy’
- 3 fully adjustable power modes allowing you to switch between them by a push of a button and change your power settings, including regen and speed limits
- Auxiliary devices connection bus to enable BMS or DC-DC converter control through the display
- The throttle control the power, not the speed of the motor(however you can switch it to speed control if you like)

Here is the specs:
Image

The cost of Mini-E is 450usd + SH = on stock.

The cost of MAX-E is 800USD + SH = they are on preorder right now, not available for sale at the moment.

Also you can order BMS board which is compatible with our controllers and is fully adjustable using from the controller display.
The price for BMS is:

16s and less: 125usd
28s 155usd
each additional 4s board would cost 13usd

Here is how the latest bms version looks like (28s)
Image

you can see 7 aux boards with individual 4s connectors grouped in 4 + 1+ 1+ 1 so minimal configuration is 4 boards up to 16cells and max config is 7 boards, up to 28cells.
Each board can be configured for 2-4 cells.

Please do not hesitate to contact us via PM or via email sales@adaptto.ru
Edited by Adaptto E-Drives Lab on Tue Mar 18, 2014 5:00 am.
For sales enquiries please contact us via: sales@adaptto.com
Technical questions: techsupport@adaptto.com
Web-site: http://adaptto.com/
User avatar
Adaptto E-Drives Lab
100 W
100 W
 
Posts: 119
Joined: Fri Mar 02, 2012 5:01 pm
Location: Moscow, Russia

Original post: The most advanced Adaptto Mini-E Controller + BMS

Postby Adaptto E-Drives Lab » Tue Mar 18, 2014 4:27 am

We are proud to offer our MINI-E controllers for sale.

Image

Controllers the following features:
Controllers major features:
- Sine wave motor power control & intelligent adapting logics higher efficiency , less heat, silent motor operation, all sorts of protection
- Very compact for the power they are pumping through
- Display to show you everything from ride statistics and “dynamics” to voltage sag on each cell (should you opt for our BMS) and allow PC-free adjustability for you to play with the settings right on spot
- Built-in wattmeter
- Fully adjustable regen, analogue (not pre-set) regen power control given you use our throttle
- Traction control
- Cruise-control
- Possibility to set range - controller will limit the power to the necessary level
- Automatic phase/halls wires combo selection = no pain with finding the right combination just make sure the +&- of the halls are connected right the rest will be done by you but electronically through the menu on the display
- Protection motor/controller overheating – there’s a thermosensor the in controller and a thermosensor port to monitor motor’s temperature and manage the power accordingly (first the display will show you an alarm warning that you are reaching a certain temperature and once it gets to high the power will be automatically limited until the motor/controller cools down)
- Square wave, and sensorless (besides sine wave (vectored) motor control modes (if halls fail -which shouldn’t happen due to overheating protection - the controller will automatically switch to sensorless mode, so you might not even notice the halls are dead until you start on a hill)
- Automatic hibernation of the system in the time you set
- Motor and battery health monitor
- Integration with BMS – you can monitor your battery or each cell, set LVC/HVC to manage your battery’s ‘life expectancy’
- 3 fully adjustable power modes allowing you to switch between them by a push of a button and change your power settings, including regen and speed limits
- Auxiliary devices connection bus to enable BMS or DC-DC converter control through the display
- The throttle control the power, not the speed of the motor(however you can switch it to speed control if you like)

Here is the specs:
Image

The cost of Mini-E is 450usd + SH = on stock.

The cost of MAX-E is 800USD + SH = they are on preorder right now, not available for sale at the moment.

Also you can order BMS board which is compatible with our controllers and is fully adjustable using from the controller display.
The price for BMS is:

16s and less: 125usd
28s 155usd
each additional 4s board would cost 13usd

Here is the how latest bms version looks like (28s)
Image

you can see 7 aux boards with individual 4s connectors grouped in 4 + 1+ 1+ 1 so minimal configuration is 4 boards up to 16cells and max config is 7 boards, up to 28cells.
Each board can be configured for 2-4 cells.

Please do not hesitate to contact us via PM or via email sales@adaptto.ru
For sales enquiries please contact us via: sales@adaptto.com
Technical questions: techsupport@adaptto.com
Web-site: http://adaptto.com/
User avatar
Adaptto E-Drives Lab
100 W
100 W
 
Posts: 119
Joined: Fri Mar 02, 2012 5:01 pm
Location: Moscow, Russia

Return to Items for Sale - New

Who is online

Users browsing this forum: JuiceMeUp and 8 guests