stancecoke's latest activity
-
stancecoke replied to the thread TSDZ2 EBike wireless standard (like Specialized Turbo Levo) - OpenSource.See the specs on the Kclamber homepage: http://en.kclamberele.com/product/1.html It's specified with 35mv/N.m. regards stancecoke -
stancecoke replied to the thread KT motor controllers -- Flexible OpenSource firmware for BMSBattery S/Kunteng KT motor controllers (0.25kW up to 5kW).Can you confirm, that the blue FETs are on high side? Drain connected to the battery + rail? The voltage on low side is strange, I...
-
stancecoke replied to the thread KT motor controllers -- Flexible OpenSource firmware for BMSBattery S/Kunteng KT motor controllers (0.25kW up to 5kW).OK, so it's a nine FET... The blue ones are the high side FETs?! The 13V should be the output voltage of the LM217. You could check the...
-
stancecoke replied to the thread KT motor controllers -- Flexible OpenSource firmware for BMSBattery S/Kunteng KT motor controllers (0.25kW up to 5kW).You can check the voltage on the gate pins of the MOSFETS. On low side, they should be about 5V, on high side a little higher than half...
-
stancecoke replied to the thread KT motor controllers -- Flexible OpenSource firmware for BMSBattery S/Kunteng KT motor controllers (0.25kW up to 5kW).I see, you print out the duty cycle now, too. Everything seems to be OK on software side. So I guess, there is a hardware fault. Do you...
-
stancecoke replied to the thread KT motor controllers -- Flexible OpenSource firmware for BMSBattery S/Kunteng KT motor controllers (0.25kW up to 5kW).Sorry this is the register for a STM32, you have to look up the register of the STM8
-
stancecoke replied to the thread KT motor controllers -- Flexible OpenSource firmware for BMSBattery S/Kunteng KT motor controllers (0.25kW up to 5kW).uint_PWN_Enable is not exported from the ACAsetPoint.h :-( Sorry, I think you have to go too deep into the code, to fix that. You can...
-
stancecoke replied to the thread KT motor controllers -- Flexible OpenSource firmware for BMSBattery S/Kunteng KT motor controllers (0.25kW up to 5kW).Sorry, again: what is your line 194 now. You don't seem to have edited the line according to my suggestion, otherwise, the momentary...
-
stancecoke replied to the thread KT motor controllers -- Flexible OpenSource firmware for BMSBattery S/Kunteng KT motor controllers (0.25kW up to 5kW).?! What is your line 194 in your main.c now?! You have untervoltage now, (2048) didn't you attach the battery?
-
stancecoke replied to the thread KT motor controllers -- Flexible OpenSource firmware for BMSBattery S/Kunteng KT motor controllers (0.25kW up to 5kW).Hm, seems like the PWM output is not enabled. You should check the state of the variable uint_PWM_Enable. I don't know, if the BluOsec...
-
stancecoke replied to the thread KT motor controllers -- Flexible OpenSource firmware for BMSBattery S/Kunteng KT motor controllers (0.25kW up to 5kW).But the log is OK. The controller reacts to the throttle as expected. Connect the motor and try again, the 4th column should change with...
-
stancecoke replied to the thread KT motor controllers -- Flexible OpenSource firmware for BMSBattery S/Kunteng KT motor controllers (0.25kW up to 5kW).Push the throttle, then second column should change. ui16_control_state, (uint16_t) uint32_current_target, PAS_is_active...
-
stancecoke replied to the thread KT motor controllers -- Flexible OpenSource firmware for BMSBattery S/Kunteng KT motor controllers (0.25kW up to 5kW).Hm, you pictures show a duty cycle of 255, this means full power. So something's really wrong. I'm not familiar with the BluOSEC App...
-
stancecoke replied to the thread KT motor controllers -- Flexible OpenSource firmware for BMSBattery S/Kunteng KT motor controllers (0.25kW up to 5kW).Have you read the wiki carefully...
-
stancecoke replied to the thread Lishui "Open Source Firmware" project / KingMeter 5S.Yes, this is a simple cut of the power, you would have to add a map function to improve that behaviour...