Search results

Date Relevance Most replies

  1. veloman

    Ebrake pinout - Higo connector - programming 600C display

    Found it
  2. veloman

    Ebrake pinout - Higo connector - programming 600C display

    Throttle and pas still work, so I guess I'm lucky. Where can I find a pin diagram? Tried looking around, just see the colors. Thanks
  3. veloman

    Ebrake pinout - Higo connector - programming 600C display

    I have a Grin superharness kit, but did not buy an ebrake. I want to program the 600C display. Which of the 4 pins on the ebrake connector do I short to replicate an ebrake signal? I tried all combos, except for shorting them all together. Anyone know?
  4. veloman

    Infineon controller with CA plug

    I had an idea yesterday to go through the advanced settings and made some changes. Now it's working fine. I think it was a throttle signal voltage. It was v2 CA, pretty old.
  5. veloman

    Infineon controller with CA plug

    My old 12 fet infineon controller has been acting up when the CA is connected. Who sells these nowadays? It needs the CA direct plug connector. I'm only running 20 amps, don't want a big expensive controller.
  6. veloman

    Hall throttle issue, signal voltage too high?

    Before attempting to program, I retested with the old throttle and then the new and had no issues.
  7. veloman

    Hall throttle issue, signal voltage too high?

    Thanks AW, you always have such good replies. I'll look into the programming.
  8. veloman

    Hall throttle issue, signal voltage too high?

    Motor starts creeping upon powering on controller. Wires are correctly matched. Signal voltage with no throttle depressed is 0.85v. Throttle operates normally when depressed. It seems I need to lower the base signal voltage? How do I do that? Controller is a Kelly sine wave. Motor is large...
  9. veloman

    What type of motor for a mini dozer?

    Thanks for your input. I will consider the flywheel issues. The motor does not have a heat issue. The problem occured within a few seconds of starting. The controller hit a stall situation. It's like riding your ebike at 10mph then applying the brakes hard down to a stop while continuing to...
  10. veloman

    What type of motor for a mini dozer?

    Technically it's a Mars ME0201013101. Most of the conversion details for the tractor is here http://www.evalbum.com/5578 The walk behind has a solid axle, that's why I added the swivel caster to allow it to turn by applying weight on one side of the handlebar. I may have made a mistake with...
  11. veloman

    What type of motor for a mini dozer?

    The machine I built is not actually a dozer, but a mini wheeled loader/walk behind tractor. I still need it to dig into the ground a bit to load the bucket or do light grading. I made a rear plow for it, in addition to a front dozer grader blade. It's a wacky mess, really an experiment. Single...
  12. veloman

    What type of motor for a mini dozer?

    Yes, hydraulic system for traction is the other option. Though I rather not go that route yet. Of course the drawback is efficiency loss. But it works for high force/torque. The flywheel would put all it's energy into the drivetrain. That kinetic energy would balance the load requirements as I...
  13. veloman

    What type of motor for a mini dozer?

    I'm looking for expert opinions on what type of motor system would be suited for an application where the motor and controller will see high current near 0 rpm. It will be geared for very low speed. This topic is not about gearing. Top speed is 3mph, but it will see speeds down to 0 at full...
  14. veloman

    "Self-Learning" wire- please teach me

    Proper steps: With vehicle off the ground, Connect all wires by color. Connect self learning wires Turn controller on Should spin on its own. If direction is correct, disconnect self learning wires. If direction is wrong, twist throttle little and release. It should reverse direction on its own...
  15. veloman

    13s jst balance connectors

    I need 10 male and 5 female 13s jst-xh balance connectors. Either bare or with wire. What's a good source for jst-xh. Mouser is not looking like they have it. I'm trying to put 5, 13s packs in parallel, using one bms. I could get by with any other small style 14 pin connector (5 of male and...
  16. veloman

    Aerodynamics

    This is long gone now, but it was an effective coroplast fairing I had built on my emoto conversion. I think it went from 70 to 50wh/mile in the 30-50mph range. Can't remember exactly anymore. Nowadays I just use my old ebike with no fairing since I sit on a normal seat and don't ride as fast...
  17. veloman

    Winter garage sale - motor wheels, stuff, & a bikeE

    I've purchased from Neptronix multiple times and would not hesitate to do business with him again.
  18. veloman

    DD Hub as a mid drive motor pros and cons?

    by Chalo » Dec 27 2020 3:23am "If it were me, I'd make a plate with the 44mm 6 bolt pattern to fit the disc rotor interface, and a 74mm or 110mm 5 bolt pattern to fit any one of a number of chainrings. 74mm for rings under 34t, or 110mm for rings from 34t up. It would be easy enough to get it...
  19. veloman

    DD Hub as a mid drive motor pros and cons?

    The problem with moto front sprockets is that the largest bore is 20mm and its splined. Drilling out the hardened steel is a challenge. Rear sprockets usually have a too large bore for the 44mm disc rotor hole diameter. So custom is probably the only option.
  20. veloman

    DD Hub as a mid drive motor pros and cons?

    Is there an off the shelf sprocket that can mounted to the 6 bolt disc rotor holes? Or are the guys building these mid drives customizing motorcycle sprockets to fit on the hub side cover?
  21. veloman

    New 80 volt push mowers

    Has anyone got these batteries figured out? Mine was working fine I I think I reversed the connection to my mower and blew the fuse. I was able to replace the fuse and it shows 78v now but it won't charge. Charger light doesn't come on at all but the battery meter lights up as usual. Same result...
  22. veloman

    Winter garage sale - motor wheels, stuff, & a bikeE

    Any cheap bare DD hub motors? Does ebikes.ca not have their year end sale anymore?
  23. veloman

    New 80 volt push mowers

    I believe the switch box is a simple on/off switch. I'm not sure which wires get shorted.
  24. veloman

    Does this look like electrical failure?

    Good advice, thanks guys. I ended up reporting her to ebay.
  25. veloman

    Does this look like electrical failure?

    I want to prosecute her but yes, I'm more concerned about it affecting my ability to sell on eBay where I've been making some decent money. I've read numerous stories about eBay suspending accounts in similar situations. This criminal has a convincing story with elaborate detail and eBay may not...
Back
Top