Search results

Date Relevance Most replies

  1. Parad1gm

    Tsdz2 not turning on after charging

    After a full charge my bike doesnt turn on. Ive heard of some tsdz2 bikes not working when over 54v, but this one has OSF and also isn't this just the motor power and not my lcd etc? Maybe I have a loose connection somewhere. Any help would be appreciated Thanks
  2. Parad1gm

    TSDZ2 OSF Configuration for max speed

    I thought opening the throttle outputs at full speed, pedaling is faster?
  3. Parad1gm

    TSDZ2 Hardware upgrades (MOSFETs, Capacitors, Traces, Shunt and temperature)

    It is casainho fw
  4. Parad1gm

    TSDZ2 Hardware upgrades (MOSFETs, Capacitors, Traces, Shunt and temperature)

    I have the 860C, and I believe its mbrusa but I'll double check..
  5. Parad1gm

    TSDZ2 OSF Configuration for max speed

    Ok thanks, thats good to know
  6. Parad1gm

    TSDZ2 With 15S (55V Nominal/63V Max)

    For lead acid batteries I could see many situations this would be useful as well. Basically, all I'd need to figure out is how I can get max speed/performance just from the pedals..because come to think of it when the throttle was connected the speed with open throttle using a 52v pack was...
  7. Parad1gm

    TSDZ2 With 15S (55V Nominal/63V Max)

    1500W regulator? Thats a great idea. How do you gauge the remaining capacity? I think the cells I'm using pretty much stay near the top end performance wise until they need charging, but good idea. Haven't thought about that. Does it screw with the current though, reducing performance ?
  8. Parad1gm

    TSDZ2 OSF Configuration for max speed

    Is there any way to configure this motor, so I can achieve the same max speed with the pedals, that I can with the throttle?
  9. Parad1gm

    TSDZ2 Hardware upgrades (MOSFETs, Capacitors, Traces, Shunt and temperature)

    Is this firmware any different from the OpenSource-Firmware v.04 I'm running?
  10. Parad1gm

    TSDZ2 Hardware upgrades (MOSFETs, Capacitors, Traces, Shunt and temperature)

    Thanks
  11. Parad1gm

    TSDZ2 Hardware upgrades (MOSFETs, Capacitors, Traces, Shunt and temperature)

    Nobody has any input on this?
  12. Parad1gm

    TSDZ2 With 15S (55V Nominal/63V Max)

    Anyone try this? Does the OSF support changing the top end voltage? The capacitors and mosfets I believe are good up to 80V stock
  13. Parad1gm

    TSDZ2 Hardware upgrades (MOSFETs, Capacitors, Traces, Shunt and temperature)

    Has anyone tried upgrading the hardware of this motor/controller to beef this thing up? Like upgrading the: -Mosfets to IRF4410A, which should be compatible without swapping out other components, such as resistors. (TSDZ2 uses 6x TK80E08K3)...
  14. Parad1gm

    TSDZ2 OSF for all displays, VLCD5-VLCD6-XH18, LCD3, 860C-850C-SW102.

    The cables appear to be plugged in. I got the Tsdz2 pre-flashed, but have an stlink USB adapter, I’ll try flashing it later today, thanks. One thing, is I did short the wires while working on it, but momentarily after power was disconnected Ted as well. This caused Avery small spark. I hope...
  15. Parad1gm

    TSDZ2 OSF for all displays, VLCD5-VLCD6-XH18, LCD3, 860C-850C-SW102.

    I have a problem. Just got my bike setup, and now when I turn it on it says ‘wait’ and then ‘error brakes or comm’ I have no brake switches installed. Do I need to install /restore option bytes or something? (Something I’ve reason another thread) Thanks I’m using an 860C Firmware 0.20.1C-4.1
Back
Top