Search results

  1. S

    Rad Power Headlight

    I used a spare two pin Julet connector, that I plugged into his Rad's headlight voltage feed connector. Used the multimedia to determine which pins were positive and negative.
  2. S

    Rad Power Headlight

    Thanks for the info! Here is the connector photo.
  3. S

    Rad Power Headlight

    Question, My neighbor upgraded his Rad headlight, and he gave me his standard headlight. Link to website product I will use this on a current non-Rad bike. According to Rad's website it is rated for 48 volts. What I need to know is : 1. What is its voltage range? 2. What are the Juliet pin-outs...
  4. S

    1500 Watt Leaf Motor Pas Issue

    Good Idea. Still want to fiddle around and make a fixed speed throttle. I spent the time to put Julet connectors on all the wires vers the plastic crappy ones, so I hesitate to start that all over again with a new controller. I will measure the voltage on the signal wire while the rear tire...
  5. S

    1500 Watt Leaf Motor Pas Issue

    PAS workaround: 1. Install a 2nd throttle mechanically fixed to 10 mph with a momentary push button to activate then I can add my pedaling. Trying to hold the throttle fixed at 10mph is hard to do. 2. Send down the signal wire with a momentary push switch the 5 volts reduced to 1-2 volts...
  6. S

    1500 Watt Leaf Motor Pas Issue

    You have to match the display to the controller. The controller that came from Leaf is NOT a KT. See attached photo.
  7. S

    1500 Watt Leaf Motor Pas Issue

    From what I have read on this forum, the display is only half of the equation. The motor controller may be limited by design or oversight not to provide a lower PAS setting. Further examples of this are located @ Help Programming controller - Duotts C29 - Chinese E-bike PAS is very bad
  8. S

    1500 Watt Leaf Motor Pas Issue

    I don't have a speed mode that I can see. Level one is 20mph with a 52-volt battery. I have attached the manual.
  9. S

    1500 Watt Leaf Motor Pas Issue

    While I pedal it keeps accelerating, with the rear tire off the floor until it gets to 45 mph, which is the top end. Did find a number of posts with the same situation that PAS is fixed to Max speed, depending on make and model of the display and the controller.
  10. S

    1500 Watt Leaf Motor Pas Issue

    Installed a Leaf 1500 watt motor. Description here. The issue I am having is when using pedal assist. The motor keeps accelerating to its top-end speed. I am unable to add human power to the bike using PAS. (Ghost Pedaling) Current menu settings: P11: Assist Sensitivity: 24 P12 Assist...
  11. S

    Grin’s perspective of Ebike fires

    Excellent video! Curious about what flame-retardant epoxy is being used for potting the batteries? Found this interesting video
  12. S

    Leaf Hub Motor Question

    Excellent thread, thank you for the link.
  13. S

    Leaf Hub Motor Question

    I reached out to Leaf inquiring about connectors. Their response with a photo. "We can make 1500w motor with below waterproof cable." No indication in the response that the motor controller comes with the proper cable to interface.
  14. S

    Leaf Hub Motor Question

    Does anyone have experience with the Leaf brand of hub motors? 1. Do the motor connectors have waterproof connectors similar to Julet and or HICO connectors? 2. What precautions do you take if the motor connections do not have the above connectors? 3. How do you protect the motor controller...
  15. S

    Anyone have Rear Radar Alert?

    Has anyone mounted their Garmin Radar to the rear of their helmet?
  16. S

    Votol EM-100 & EM-150 controllers

    I have associate that has a QS CT-22 digital programmable display along with the Votol EM-100 controller on a Huck Stinger 3000 watt bike with a 72volt 30ah battery lithium-ion battery. He has recently experienced the motor cutting out when riding in temps around 44 degrees fahrenheit. Any...
  17. S

    Women's Townie conversion

    Yes, Thank you.
  18. S

    Women's Townie conversion

    Looking for a post that I now cannot find of a gentleman who converted his wife's Townie to a electric mid drive. The particular post had photos and one of his wife on the beach with the bike. Tried endless searches with no avail. Thoughts? Regards Steve
  19. S

    Bafang BBS02 parts

    Thank you for your suggestions. I got this information from a overseas Bafang bike shop. They could not tell me what number went with what seal. Here are the Bafang Numbers for seals they call it “BF-Code”: Rubber Seals for BBSHD (3 numbers): 1401210100002 1401210200001 1401210200004 Rubber...
  20. S

    Bafang BBS02 parts

    Was able to source the phase wire grommets @ https://www.greenbikekit.com/bafang-8fun-bbs-kits-and-spare-parts/8fun-bbs01-bbs0b-maintenance-repair-related-parts/bbs-motor-phase-wire-rubber-seal.html Still searching for that elusive rectangle grommet.
  21. S

    Bafang BBS02 parts

    Good idea, but nearly impossible to remove the original existing white sealant without tearing the original grommet. So a mold of this would not be ideal. Some folks report they carefully use a Xacto knife to remove original sealant. Thank you.
  22. S

    Bafang BBS02 parts

    Does anyone have a resource for parts for a Bafang BBS02? Looking for internal grommets for phase wires and control socket going to motor. At some point will need gaskets for both sides of motor casing. Thank you.
  23. S

    Townie 7D front axle

    Chalo , Thank you will try local bike shop.
  24. S

    Townie 7D front axle

    Hi Markz, found this, need to confirm measurements, also a few on E-bay that may fit. :? https://wheelsmfg.com/products/hub-parts/all-cones.html :) Thanks for your response.
  25. S

    Townie 7D front axle

    Looking for a replacement front axle for a Townie 7D. I really only need the left and right cones. Parts are just hard to find period. Axle: Dia: 8.25mm Length: 108mm Cone: 12.25mm length 15mm Dia
Back
Top