Recent content by arka

PITMIX Great, I will connect it today. I am glad that such a small panel is possible to integrate with Nucular :)

I am glad that you like my drawing, especially that it was made on an iPhone which was not easy :) can you answer this question? If not, it is pointless to fill the post with empty content without meaning. Thank you.

If I connect this 4-button panel, can I configure it to work: Button 1: Speed Mode 1 Button 2: Speed mode 2 Button 3: Speed Mode 3 Button 3:direction of motor rotation Forward/Reverse But I would like it to be possible chose function with a short press so that I don't have to hold the button...

What is the P3? I have a problem with a 2020 Surron that is an electronic throttle. In the past it turned on correctly meaning the display said P1 and then E2. Since yesterday it displays P1 and then P3 and the throttle does not work. No other errors are displayed. Any ideas?

70 or 140 if you put them in 2 rows.

I'll start with myself. I've had GEN 2 for a few days now. My bike is downhill Mondraker Summum 27.5' whell. I have a 52V 17.5Ah Sanyo GA 840Wh 14S5P battery. The rear gear is dedicated for electricians Sram EX1 / 11-48s, in front I had 11/63T with a 38T sprocket but I changed the sprocket to...

A request to people who have had CYC Motor for a long time or have more experience. Could you share your CODE SETTINGS by adding them to this thread? The next people could add something from themselves and together we will create better settings. I know we have different drives and different...

Dear casainho I was just on a test drive and I think I know what's going on. The problem comes when I hold up and turn on the lights. Then it stops reacting. When I turn it off, it goes back to normal. Connect the lights directly to the battery and there should be no problem. At the same time...

I want to go for a long ride with my little son tomorrow, so unnecessary stops are not advisable :-) So far I've been using the stable version 0.19.0 + Bafang 850C but I'm having problems with the engine overheating and I need to have a temperature preview showing the current exact value - that...

Unfortunately, due to the epidemic, getting any 850C in Poland is not possible :( So it is not possible to upload new firmware versions to older 850C (TFTGDV4A60 HHY.100 V5.2 201709142025)? Then which last version will be possible to install on this old display?

I have two displays: - older 850C (TFTGDV4A60 HHY.100 V5.2 201709142025) - newer 850C (TFTGDV2.3CL60 HH2.0 V5.2 20190506 0104). I can easily upload any custom firmware to the new 850C. I use bootloader to upload. I can't upload any of the newer firmware (v0.7.0, v0.6.0) to the old 850C every...

Did any of you combine the TSDZ2 with the drive system Sram EX1 used in the best Bosch motorized electric bikes (Cube, Hibike)? Sram EX1 dedicated to electric bikes with a special thicker chain and 8-row 11-48T cassette, gears can be changed even under load...

I bought a complete set of SRAM EX1 (rear sprocket, derailleur, chain, shifter) for TSDZ2 motors: https://www.sram.com/en/sram/mountain/series/ex1?filters=&sort=Relevancy&page=1 Normally the front sprocket for these sets is with a Bosch engine: https://www.sram.com/en/sram/models/cr-xsnc-bos-a1...

I have an 850C display, but I want to look on the wiki, thank you.

Casainho - So finally you showed us the reason why you are doing such cool custom firmware - it is your son with whom you have great fun on bikes :-) Unfortunately, it is not possible to mount the front derailleur to this frame, because there is no way to screw it. To install the TSDZ2 I will...