Recent content by Mr Lowbank

Hi My charger shorted out today :? I pulled it apart and found a blown capacitor. has anybody seen this and fixed it? Could I possibly solder in a new capacitor or it there likely to be something else wrong? first I would need to know the specs on the capacitor so i can get a replacement...

Bike fell down a hill and I think the side impact did the damage rim was OK. I respoked the wheel spreading the missing ones around the rim and went riding the next day. after 2 hours (not backing off much) I had another 10 or so broken spokes and was luck to make it back to camp without the...

Maybe, but don't think so, see photo on my post Sat May 31, 2014. The number one reson to go to a motorcycle rim was to stop getting pinch flats that I suffered a lot with the bicycle rim. I was also destroying the stock Bomber rims. The reson this happens is because the back wheel weighs...

I have a Email form HH today saying "Unfortunately, our 12 gauge moped nipples are out of stock indefinitely and we no longer are cutting custom spokes because our machine broke" The spokes I have been using from HH with the crystalyte x5 and the Prowheel racing 19x1.4 rims are the 11/12...

Thanks for the comments Markisses. I did spend some time trying to get this right. but you have make me revisit this. There are some rules of thumb that put copper at 2000A/in² which is 3.1Amps/mm² or 21.7Amps for my 7mm² copper strip. But this contradicts other information. Nobuo's table of...

I tried for a long time to come up with a design that could use cell holder but will not fit in bomber unless you do what what Sigmacom did.https://endless-sphere.com/forums/viewtopic.php?f=14&t=61604 so it will be the hot glue and stiff Glass Epoxy sheet method...

Hi All Have been mining the Endless sphere for information to build a new pack for my Bomber #127. Thanks to forum members for all the great information. I decided against 20s14p as it would be a tight fit, weigh more and I really don't think I need the amps. I'm hoping for Sanyo NCR 18650GA...

Hi Dlogic Its been a while since someone has posted here but i will try my luck for some advice. I have had my V-Boxx Repaired by manufacture about 1000km ago. I noticed the output shaft loose and tightened the big hex nut inside sprocket but shaft is still wobbly. It has been like this for some...

I had the same thing, sounded like a little bird was following my. The Problem is that the DNM Shock bottom eyelet/bearing is Level with the Black housing and rubs on the shock mounting tags. I fixed it by removing the bearings and grinding/filing the sides of shocker so there was some...

Hi What should I do with my old Battery ? It's from bike #127 Only did 91 cycles or 981Ahs was getting 12Ah out of it before hitting BMS off road riding. Hooked it up to my bike last night after it had been sitting for 4 weeks off charger. went for short ride them ran the bike at WOT on stand...

Pic of the bomber with Shinko SR241 2.75x19 and Prowheel rim mounted to 5405. Wheel weighs in at 18.5kg (stock bomber wheel 17kg). WOT The 5405 seems slow off the start but then has a big hit of power at around 20km/h. In hind sight my original motor must have been a 5404 which I think I like...

Shinko SR241 2.75x19 With Prowheel rim mounted to 5405 with 11/12(3 -2.7mm)x 123mm spokes 18.5kg Old wheel Bomber wheel with Duro Razorback Tuffy and Slime 17kg the Shinko is about 10mm less diameter with full tread over Duro with no tread. What Preasure do you run with the Shinko? I tried...

I have a question. what tyre levers do people carry in the camel back with the MC Setup. Or is the theory you won't need any.

As Johnrobholmes said, no washers required

Pro wheel racing 19x1.4" rim laced up to Rix's old 5405, using Holmes Custom Moped Spokes 11/12 gauge (3 -2.7mm) 16mm nipple 123mm long. Spokes ended up about 5 mm shy of the head of the Nipple. I didn't make any mods to the rim..What do you think about the angle of the Nipples? Should I...