methods
1 GW
SOLVED: 24V contactor not compatible with voltages over ~110V
https://endless-sphere.com/forums/viewtopic.php?f=38&t=88679&p=1293374#p1293374
Error list that I reference: http://jan.peman.com/hacks/EmergencyErrorCodes.txt
Error I am seeing on a new setup: 0x5185 Alg Out Off with FS
This setup has a pot input on Foot Brake, no foot switch, and my intent is to regen with it. I suspect the error revolves around this domain.
Error in context from above list:
0x5181 Dig In Wire Off
0x5182 Alg In Wire Off
0x5183 Alg Out Over I
0x5184 Alg Out On with No FS
0x5185 Alg Out Off with FS
So... Dig means digital
Then Alg must mean analog? May be wrong on that.
guesses
5182 detected when a signal rails
5183 detected when measured I over acceptable for longer than time X
5184 Something to do with analog output being on... while there is no Foot Switch ? (FS means Foot Switch I am guessing)
5185 Something to do with analog output being off with a FS
From that I surmise that whatever "Alg Out" is.... it should be OFF with no FS and ON with a FS
The error indicates that I HAVE a FS which I do not believe I do... so off to check the settings.
FS could refer to FS1 I suppose... which I do have wired... and is acting on the system.
Ah... thinking back to something the master said...
The master said that one can not use a Foot Switch at the same time as a Foot Lever (potentiometer) as the Foot Switch will override the analog input.
Ok - removing FS1 from the software configuration and retesting.
I had mapped it to one of the first digital inputs for use as an interlock
We will rely on FWD/NEU/REV as this interlock if possible or otherwise work around
I prefer there to be a LOCKOUT so that a motor can not blast off without the user driving the throttle all the way to zero and ALSO a switch going from OPEN to CLOSED>.... i.e. if it starts up with switch CLOSED, then it must OPEN and CLOSE again to proceed.
Interlocks... them's is there's for a Reasons's ... :wink:
-methods
https://endless-sphere.com/forums/viewtopic.php?f=38&t=88679&p=1293374#p1293374
Error list that I reference: http://jan.peman.com/hacks/EmergencyErrorCodes.txt
Error I am seeing on a new setup: 0x5185 Alg Out Off with FS
This setup has a pot input on Foot Brake, no foot switch, and my intent is to regen with it. I suspect the error revolves around this domain.
Error in context from above list:
0x5181 Dig In Wire Off
0x5182 Alg In Wire Off
0x5183 Alg Out Over I
0x5184 Alg Out On with No FS
0x5185 Alg Out Off with FS
So... Dig means digital
Then Alg must mean analog? May be wrong on that.
guesses
5182 detected when a signal rails
5183 detected when measured I over acceptable for longer than time X
5184 Something to do with analog output being on... while there is no Foot Switch ? (FS means Foot Switch I am guessing)
5185 Something to do with analog output being off with a FS
From that I surmise that whatever "Alg Out" is.... it should be OFF with no FS and ON with a FS
The error indicates that I HAVE a FS which I do not believe I do... so off to check the settings.
FS could refer to FS1 I suppose... which I do have wired... and is acting on the system.
Ah... thinking back to something the master said...
The master said that one can not use a Foot Switch at the same time as a Foot Lever (potentiometer) as the Foot Switch will override the analog input.
Ok - removing FS1 from the software configuration and retesting.
I had mapped it to one of the first digital inputs for use as an interlock
We will rely on FWD/NEU/REV as this interlock if possible or otherwise work around
I prefer there to be a LOCKOUT so that a motor can not blast off without the user driving the throttle all the way to zero and ALSO a switch going from OPEN to CLOSED>.... i.e. if it starts up with switch CLOSED, then it must OPEN and CLOSE again to proceed.
Interlocks... them's is there's for a Reasons's ... :wink:
-methods