Recent content by A..dam

@Jonca, first few points: 1. I have the throttle which make applying&measuring of power going to motor far more easier than PAS. 2. The KM5S appears to produce quite wobbly readings when the power is lower than 100-150W 3. On that Alu frame I have (fortunately or not) a steel fork, so I hope...

without failing of course... for short bursts of hill climbing power. I have Q75 (200W) interfaced to LSW-675 (7A continuous, 15A peak) with KM5S display which is capable of live measuring power in W, and also limiting current within 1-15 A adjustable range. Some easy math: 7A x 36V = 250W...

WARNING: DO NOT USE S06P controller with Q75 Changed the S06P to LSW-675 and it works flawlessly with Q75. BMS battery is making false claims that S06P is compatible with Q75!!! Note about switching controllers. 1. Disconnected the sensors from S06P and measured voltages on connectors 2...

Thanks Jonca! Feedback from you, including German website comments was what I waiting for. Will be ordering that LSW-675 controller, too bad that my existing LCD-S1 is not compatible with it. Regarding my conversion: I also wanted an ultra-light setup, hence the Q75, especially that I am only...

The 214 is a correct # based on the available information. I have tried changing this number in increments of one in the range 204-224 and increments of 5 beyond this range. The only way to reduce stalling and horrible squeal is to reduce power by inputting a value well below 214. So my...

From BlueMySky Battery. Why? I have the 201 rpm in a 20 inch wheel with S06P controller (plus LCD-1 S) which lose sync and thus power plus get a horrible squealing noise with high power at low speed. Just when I need torque to climb a hill! BIG problem. One solution to this when using a S06P...

SOLVED... Shorting 12.8V socket does indeed switch on power from battery to the output terminal. Good. But flipping the power switch also produced voltage of ~ 13V on terminal for the LED voltage meter of the battery. I have tested the LED meter and it needs full battery voltage - 4 green...

Soldered the new PCM to my old battery 1. Battery is charging, charging stopped at 41.4 v, measured at the PCM, so far so good. 2. Found some old diagram of a PCM from a QUAWIN website (they do not make it anymore) see photo 3. The diagram is very similar to my board except for a few components...

I bought this product: https://bmsbattery.com/bmspcm/718-10s-lithium-bms-system-for-bottle-battery-with-5v-bms-pcm.html L-B36-10S/15A-1129 On a PCM there are TWO white connectors for TWO wires each Which(!) socket is for LED battery meter and which one is for the power switch? Picture of the PCM...

save of course for USB output... https://bmsbattery.com/bmspcm/391-10s-lithium-ion-bms-for-bottle-battery-case-bms-pcm.html has PCM-L10S15-923 (A)+(B) https://bmsbattery.com/bmspcm/718-10s-lithium-bms-system-for-bottle-battery-with-5v-bms-pcm.html has PCM-L10S15-923 (A)+(C) #1. I have checked...

I got 11.6 Ah Panasonic bottle style battery https://bmsbattery.com/ebike-battery/734-36v116ah-bottle-ebike-battery-pack-with-charger-battery.html 1. When arrived, battery voltage was 41.5V and 4 segments on the capacity indicator were green. 2. After using it for a dozen kms or so voltage...

I told BMSB representative that there is a problem with the battery NOT the charger more than 3 weeks ago. After convincing them about that, they now want me to troubleshoot battery by opening the case. Every e-mail exchange takes 4-5 days so it might take till Christmas ;-( to resolve the...

It is impossible for any cell(s) to be fully charged at this point. The BMS MUST BE the culprit. I have offered to BMSB trying to charge with a different charger, and waiting now for their response as I do not want to be "blamed" for any damage. The other charger I have in mind has fully...

I connected a voltmeter 20 kohm/V to a charging port, (NOT discharge terminal) it shows voltage of 23.4V for a few minutes and than it jumps to the current voltage of the battery which is now 36.0V. It needs some very minor current to flow to show the full voltage. When I connected a digital...

Assuming (!) that all batteries are very similar in parameters, you can use ONE 18650 diagram as an example. capacity vs voltage is highly current related Google it &check images...