Recent content by gone_walkabouts

Cool - so seem that you can parallel the main leads and parallel the balance lead. Will do it outside just in case.Yes made the mistake of jointing two pack before in parallel with 20% voltage differences..i did not have a BMS in the lower one so it ran away....... See video of local fire...

I have had success hooking up smart BMS's that you can connect to via bluetooth or a PC They cost little more but as you van see the voltage of each cell then you know if it is working or not or balancing or not Just get the right amp rating and cell series plus chemistry for your application...

Looking to hook up a BMS to a 14s 2P pack. I am fine with the BMS side as I have done this before...on a 13s pack. The question someone might be able to help we with is around if it OK to hook up 2 X 14S Lipo pack in parallel and then hook up to a BMS. The 14s packs are multistars that are...

+1 to see a strengthened Beta swingarm with 150 drop outs. Surely this could just be an option once the guys get a chance to design and build it. At Shanghai airport right now coming home from the Shanghai bike/ebike show with a Mxus v3 - tempted to open the box to see axle width.Reading up...

thanks - yes that is what i was suspecting that the weight allow for this. Interestingly when the issue first arose, my wife could get the bike going with her weight and then turn the throttle gently and off see would go....then about 250km later this was no longer possible..i wonder if a...

hi there, I have been building ebike for a number if years now and have come across a issue that has me scratching my head....... The set up is a 4 year old Infinion Controller that has been set up with Crystalyte 3525 hub motor...it has been working well for years until recently. So what...

Just wondering if any Adaptto owners have had experience charging at around the 12V mark. I am looking to set up a solar charing system with some old but usable Headway batteries.I am looking to configure into 4s to suit my solar system giving a fully charged voltage of around 14.4V. I have...

Hey great videos and information - thanks for sharing Are they lipo batteries that are strapped to your back ? as a hang glider pilot this is the bit that would freak me out Yes unlikely- but a battery fire on climb out under load could never be fun ! Thought? Would be good to a system you...

Great concept - i fly myself. How do you control the wing and steer the bike on take off?

looking forward to getting the perforance stats on this one !!

Your guys are spot on....certainty bridging that bridge did not solve the issue....I have done the following 1. Bridged the bridge 2. Installed a fresh fuse for the AC input 3. Turned it on 4. Shazame as before.....blew the AC input fuse and the house fuse at the same time The charger was...

The picture does not show it too well however it very much appears this was a shunt and looks broken. If I look at board there are other part of the board that are labelled KXXX and there are just stunts. (Solder wires bridging to areas) I am assuming areas labelled K on the board are...

So I have opened the damn thing (the emc1000 charger) and to my surprise and delight I may have located the source of the issue.....looks repairable. On the PCB there appears to be a component missing (blown up), or it may be a broken shunt.(not sure) Where do I find out what I need to repair...

too answer previous posts, charger has been working fine when connecting directly to the battery I worked a bit more on this and it appeared the issue why there was no response out of the charger was a bad connection between the special lead I made up to connect the charger to the parallel...

Hello hello. I thought I would throw this one out to the friendly Endless-sphere community...to help get some sanity around this ! :P I have a 20s lipo ebike that I am looking to set up so I can bulk charge in parallel. What I mean be that is to have a parallel connector running off the...