Recent content by MurderousFrog

Finally, some more recent pics. http://imgur.com/a/00y2r Also, the adaptto settings: https://imgur.com/qeiMvIN https://imgur.com/JcfZfHP Let me know if you need anything else. I also got the adaptto external speed sensor working. The problem was that the speed sensor i was using (which was...

Took me a long time to get back to you, but here I am! If you are still interested, I will upload some screenshots of the settings I'm currently running. Beware though - these are not fully optimized, when the freewheel in the rearwheel hasn't engaged yet (bike rolling or braking and...

I'm currently busy with university and work but I'll write them down for you as soon as I can find the time. Just a word of warning: Replacing the original controller was everything except easy. Also currently the external speed sensor does not work and the adaptto itself is far from perfect...

I didn't have time to post any updates in the last month because I was busy finishing the bike! Finally now I can share it with all of you. First off, it's an absolute blast to ride. Even though it has less power than my last buildit effortlessly pulled me up every grade i could find...

Oh well that solves it. Thank you very much. There was no magnet included. Gotta figure out how to use it because the adaptto regen/thr cutoff wire is already used by the external speed sensor....

As most of my exams are over, I had some time to work on the bike. Pictures tell more than a thousand words: Testfit of all components on the bike. It is still comfortably light. Battery is 10 packs of 5Ah 4s hobbyking lipo. This equals a 74V nominal 10Ah battery, and I still have room for 5Ah...

I already have the adaptto from my last build and I am not afraid of the electronics and wiring and stuff, removing the BBSHD controller from the casing without damaging it is the hard part right now. Also, there's good news and bad news. The good ones first: I received my package from lunacycle...

After my misadventures of trying to design custom bolt-on dropouts to fit a MXUS 3000 to my giant reign sx 2014, 3d-printing countless models which were just as unfitting for my frame as they were expensive and finally giving up after over a year I said to myself: screw it. I'm going mid-drive...

Thanks for the help, I will try it out as soon as I can.

I still have the same issue with my MINI-E... The bike ran fine for the first ~50 kms. Beautiful acceleration, everything fine. Then after two days the throttle started cutting out under (more or less) heavy acceleration >2.5kw and a !HALLS! error is displayed until I release the throttle. Below...

I switched the halls, cleaned and greased the "shot" bearing (which now runs perfectly...) and ran autodetect again, but the same issue persists. I am now using shielded wires for the hall and temp signal cable. On hard acceleration >2.5kw the throttle cuts out and a !HALLS! error is displayed...

Hey Mike, It's just such a nice frame, i couldn't ever cut it open, the only thing i might have to do if I used a rear hub, is to modify the through axle so they are dropouts and I can fit a hub axle in there.. Maybe I can build adapters to fit onto the through axle holes/disk brake mounts? That...

Sadly it is a through axle and not a QR, can't easily fit a rear hub axle into it without modifying and cutting the frame open. And since I got used to the power of my Adaptto Mini-E and up to 5kw on tap, its hard to imagine less power, although the low weight is a big plus. I've ridden a...

I found some pictures from the Interbike '15 where Dr. Bass is posing with his NYX Bike and Adappto. In the background there is a poster: (link from facebook) There is another model of the adaptto controllers listed, the MIDI-E, with 8kw of power. I have searched the internet as well as ES...

I think the shock reservoir would be in the way :/