Recent content by splitfire

stealth bike users. If you guys dont mind just want to know how fast can you go if a rider weighs is 250-300lbs. Is there any rider in this weight range? Sorry i dont mean to offend anyone, coz someone wants to buy my bomber and he is 300lbs. I am taking about stock bomber 20Ah 88v fullcharge...

hi do you still have the panasonic 18650. i need 168pcs., do you also pack/ weld battery packs how much do you charge?

i got 4 cycle use with my new lipo packs. i run my bike from full charge 4.2v to 3.7 theres 1 cell that keeps dropping to 3.2 when others are 3.7 . but when i charge it they are all 4.18-4.2. should i replace my cell? LuboN

How much each of those 18650? Mah? What is your batt configuration .how many cells did you use? I want to buy these batteries but I dont have spot welding.

You need a seperate bms for your lifepo4 and lipo, for charging you can charge it the same time just parallel them. The 87.6v output is actually for lifepo4. However you can also use that in lipo 21s it will be 4.17v per cell. Or increase your xharging voltage to 88v. Lifepo4 can handle up to 3.7v

i had a problem with my charger before. When i bought it new it was 87.6v which is right according to the label. After 3months of not using it, it drops to 86v output. I tried to open my 6amp charger. I saw 3 variable trimmers in the board. I tried playing 1 of the trimmer and it works. I got it...

My charger works up to 86.4v. It used to charge at 87.6. Dont know the problem but that isnt a very big deal for me. When my battery died. I checked all my cells individually they are at 3.7v but there is one cell that has 3.3v. I will keep monitoring that cell every time I charge and probably...

Dont know where I can get a cheap 72v 5-10A. For now ill use my charger. Yup bms works great. I just dont like the LVC setting at 77v . So what will I do is when the LVC kicks in, I have my bypass connection when I need to run. It will still be balance for charging and for running it till it...

Oh I c thanks Ykick....ill just gonna make a connection where I can bypass the bms just for emergency use and install a lipo reader so I can still monitor them.

I got the d131s 21s lipo bms that i want to adjust the LVC. I just had my bms hooked up today. I was running it to know when will it cut off and it cut off at 77v isnt too early 3.7v each cell i know 3.7v is ideal but i want to run my bike a bit longer. According to bestech website this d131s...

Hey guys. My rubber is almost worn out. Just want to know what tire is good for this 120lbs machine. I am not looking to spend too much. Is it ok to use a single ply wall tire?

Cool. Thanks for the pics. I already assembled my packs. And did not go bang :). I just dont know what gage wire to use for power cables #10 or #8. Is it thick enough?

Thanks dnmun. Yeah better to connect the tabs when connecting them in series . Can you show me pics. I know ive seen you pics somewhere were you unwrap the batteries use a clam and solder the leads . I just cant find it again or pls send me the links. Thanks

Thanks dnmun. Yeah better to connect the tabs when connecting them in series . Can you show me pics. I know ive seen you pics somewhere were you unwrap the batteries use a clam and solder the leads . I just cant find it again or pls send me the links. Thanks

Hi Dogman dan thanks for the info . I am going to pack up my batteries I will start weld all the balancing leads in parallel. Do I need to parallel my power wires too? Can you pls give me a wiring diagram. And also dont know how to connect then in my bms I have 21s lipo in total 3x 6s and 3s ...