Recent content by syco26

I have pulled the body off the 6 wire controller. Put the four wire internals in it. Put it all back together and tried it and all good. Forward as it used to with progressive throttle. Reverse switch works and goes backwards with the throttle. Thanks all for the help. It is greatly...

I just reconnected the wires the the throttle and the LED light lite up, hasn’t done this for a while. Tried the mag from the twist throttle on the hall sensor and 🥳🥳🥳 the back wheels started turning. Move the mag strip across the hall sensor and the wheels turn faster on way and stop when I go...

I may need to redo a couple of those tests above. I had the multimeter on V~. I just connected everything and wasn’t getting a result at the throttle end of the cables. Changed the meter to V with the dash line and solid line above and get 24v on the yellow cable, 0.00 on the other three when...

Sorry TC, not following. “The disconnected ground circuit” are you talking about the black lead I pulled from the 18-pin plug number 2? If so I have a bare wire one end with the exposed terminal on the other end and the couple connected plugs in between the two ends. Red probe to the exposed...

Sorry, must have stuffed up on the last test. I tested on one of the battery plug ends but was on the negative of one battery plug that goes to the positive of the other battery plug. Retested on the battery plug negative that goes to the controller. With the negative lead of the multimeter to...

Hello TC. See attached sticker on the back of the controller. Thanks Floyd, you were correct with the model number. I have also done a pretty crappy wiring diagram. Please note the pink is actually white, had to use a colour due to the white background. With the batteries disconnected and from...

Floyd it is a Curtis controller but can’t see a model number anywhere but looks very similar to what you have posted. Thanks

I have retested as per you first instructions after finding the issue with the red wire at the controller and fixing it. With the 4 loom wires not connected to the throttle. When I turn the key on, with the red test probe on yellow loom wire and the black probe on blue loom wire, I get a split...

I pulled the red pin that wasn’t getting a result and the wire wasn’t in the pin correctly. Looks like I may have pulled it out when disconnecting the main plug. I crimped the pin properly and checked again and getting 0.3 from the cut wire to the red of the main controller plug.

With the multimeter set to ohms and on the 200 setting I get 0.04 ohms from the bare wires to the first connector. Tested one wire at a time. With the first connector back in and checking from the cut wire loom back I get the below at the next plug. The negative is on the cut wires one at a...

Thanks again for the reply. I will start the hunt and get back to you. Yes all the previous tests were conducted on the wire loom in the above photo without the throttle connected. Something I totally forgot to mention, as too focused on the controller and loom, the blue and red wires...

Sorry for the late reply, was out of town yesterday. TC following your instructions, negative to the blue and positive to the yellow. With the key off I get 0.00v and when I key on I get 00.2v. With the negative still on the blue I get 0.00v on the red with the key off then when I switch the...

Hey Doc. Pictures of the first and second controller in my original post. No point in seeing photos of the third controller as I cut the Hall effect sensor out of it to try on the first controller and is now in the bin. It was basically three wires to the hall, the negative went to the LED...

So I tried to test the function of the hall sensors. On the 6 wire that is still complete if I use the red as a positive and the black as a negative onto a 4v pack I get between .8v and 3.6v when rotating the throttle controller. On the old unit with the hall sensor out of the new unit I get no...

Gave that a try but no good either. Took the third hall sensor and soldered it into the old unit but no good. Connect all the wires then key on and nothing happens. If I disconnect the wires then key on and add wires one at a time as soon as the green is to green and blue is to blue the wheels...