Search results

Date Relevance Most replies

  1. S

    Cycle Analyst with 2 shunt with new firmware

    Done :-) thank you
  2. S

    Cycle Analyst with 2 shunt with new firmware

    WOW you're the one who program this... Very impressive !!! Thank you I can now remove my 2 other displays, and only keep the CA. Still working on my bluetooth kit and I now received data :-) I'm very happy, about that. if you have a list of the data being sent through the serial output, I...
  3. S

    Cycle Analyst with 2 shunt with new firmware

    WOW Thank you so much everything work. I know that I need to be taken by the hand all the way to the end but i really really appreciate it. you did a lot of my work for me. I setup the Shunt Value at 1.00 mOhm for the Consumption from what I could find in the Help file but the watts measure...
  4. S

    Cycle Analyst with 2 shunt with new firmware

    ThI -> Throttle In , I should have understood that on the production Shunt, there is 3 wire, the green for Throttle, the Yellow for Speedo and a Black is the black a Ground ? should I connect it too ? I juste received everything I need to connect this, I am going to try tomorrow. Thank you
  5. S

    Cycle Analyst with 2 shunt with new firmware

    Thank you again I think I am getting there :-) so in the Consumption Shunt, I take the green wire and put it in position 1 of a female JST-SM and I dont connect any cable to the two other position. Then I connect this to the Throttle input of the Ezee controller. Time to go to work ...
  6. S

    Cycle Analyst with 2 shunt with new firmware

    WOW !!! Very precise and to the point And Very fast !!! Thank you Very very much. I was afraid that there were no too many people aware of the new shunt. I do have more questions :-) A The throttle input on the Cycle Analyst has 3 wires (taken from the manual. Position 1 Red: 5 Volts...
  7. S

    Cycle Analyst with 2 shunt with new firmware

    I would really appreciate any help with my problem with Cycle Analyst (CA) V3 CA-DPS and shunts. I have a solar eBike. I have two motor with each their own controller and throttle. I have bought two Shunt 1- The standard one - http://www.ebikes.ca/shunt-ca3.html will be used to...
  8. S

    Cycle Analyst and Battery Charge Cycle

    When I configure Cycle Analyst (CA), I have to specify everything about my battery in a way that CA know the Wh capacity of my Battery, Then, when I use it, the CA can give me how much Wh I have consume. Which is great Then why do CA need me to Reset it each time I put in a Fully Charged...
  9. S

    Ezee motor and 10K NTC thermsitor

    Good idea to limit the power. thank you One of the problem is speed. I won't be able to go fast. Very tight road, lots of traffic and my bike will be heavy (tent, spare part etc) for this 9000 km trips The other problem is a steep incline on a long distance. if you can see the charts there...
  10. S

    Ezee motor and 10K NTC thermsitor

    in the error code of the Ezee controller, I see Temperature Sensor Fault so I guess , there is a sensor, maybe, the Cycle Analyst just does not have access.
  11. S

    Ezee motor and 10K NTC thermsitor

    I bought an Ezee motor 350 RPM and I will travelling in mountain for a few weeks. I am afraid of the temperature of the motor combine with the fact that air pressure at those altitude is below 70 kPa, the cooling won't be optimum. I dont think my Ezee motor has a temperature sensor build in. I...
  12. S

    Cycle Analyst - Battery config problem

    Thank you :-) I guess it read 1.5 mili-Ohm of 0.0015 ohm how do I give a thumb UP ?
  13. S

    Cycle Analyst - Battery config problem

    Yes, you are right, sorry I forgot to mention Setting in my first post (but I did in the second one :-) For the shunt, I will go read the Controller right now Again my mistake because I just re-read an email form Grin a few weeks ago. I had forgot about it. You don't need a shunt if you have...
  14. S

    Cycle Analyst - Battery config problem

    Yes, I do have 58.8 it is in the setting that I see 51 V after I put 14 Cells Just like putting 1515mm for the diameter show 18.9" for the wheel. Grin Tech told me that my Ezee motor has a shunt in it, so I did not needed to buy one. in the Spec Page, I see a Phase Resistance (Ohm) = 0.049 ...
  15. S

    Cycle Analyst - Battery config problem

    I bought this battery from Grin Tech http://www.ebikes.ca/shop/electric-bicycle-parts/batteries/b5216-lim-dt.html which is rated as 52V 16.5 Ah When I received the battery, there was a sticker on it, written by hand sting 17.5 Ah. Great :-) I setup my Cycle Analyst (V3) CA at 14 cells from...
View older results
Back
Top