Search results

Date Relevance Most replies

  1. S

    Is a solar power fridge available?

    Batteries Expert Pickering has 12V/24V powered fridge 905-831-5068 batteriesexpert.com
  2. S

    Does anyone know if I can use the Alltrax Axe 7234 at 96v?

    I have an AXE 7245 with a 22 cell li-po pack 60 amp. The controller will turn on for a split second and then shut down when fully charged. So I charge my cells to 4.10 volts per cell. Works great!!
  3. S

    Nickel strip in canada ?

    What size are you looking for. I can get the tabs
  4. S

    New battery box build

    .
  5. S

    99$ for 40W solar panel at CanadianTire this week

    Thats over $2 a watt!! I can sell you Canadian Made Sharp panels for $1.30/watt. Sharp Panels 235 watt $305 each min 2 panels. Thats not even on sale...lol. For larger orders pm me
  6. S

    If you have 4k to build a electric cart, what would you buy?

    I used a 40 pitch gear on the motor, a 428 gear on the rear with a 40 pitch chain. It seems to work well. Only time will tell.
  7. S

    If you have 4k to build a electric cart, what would you buy?

    I was thinking of doing this. How perfect do you think it needs to be? Did you have any premature chain wear after? The gears are so close, only need a little material removed
  8. S

    If you have 4k to build a electric cart, what would you buy?

    I have mounted a D&D motor to the kart. I have an Alltrax 72V 450amp controller. I am having issues with the chain. I measured the chain that came with the kart, it had a half inch pitch, check the info half inch pitch is #40. So I bought 40 pitch gears. Chain didnt work. After some research I...
  9. S

    Made in Canada, eh?

    http://www.youtube.com/watch?v=x-f2LWHo2DE
  10. S

    If you have 4k to build a electric cart, what would you buy?

    If you ran two motors in series with a 90V battery that would be 45V at each motor..Correct? Would there be away to shut one motor off on the straight aways and apply full 90v to a single motor for peak speed? Or would the other motor put to much drag on the system?
  11. S

    If you have 4k to build a electric cart, what would you buy?

    This is what Steveo and I have to work with
  12. S

    Made in Canada, eh?

    Yes, depending on motor and battery size
  13. S

    Made in Canada, eh?

    Yes, the bare frame
  14. S

    Made in Canada, eh?

    It's about 16-17lbs with no fork, no shock, no crank
  15. S

    6v 4.5ah Batteries

    You will destroy them very quickly
  16. S

    Made in Canada, eh?

    ES member kriskros going for his test ride
  17. S

    Made in Canada, eh?

    Kinda like where's Waldo! lol
  18. S

    Made in Canada, eh?

    Some teaser photo's
  19. S

    Made in Canada, eh?

    Cat is outa the bag! This bike is alive and well!
  20. S

    Meanwell NES current limiting solved???

    Yes it works! I ordered 20 power supplies and we have moded 12. No issues. Has been 4 months of almost daily use.
  21. S

    Meanwell NES Schematic..almost complete

    I know this is an old post. But back in april I had bought a couple of the NES power supplies not know that the board would be different inside. After frying a couple I think we got it figured out. We have moded about 12 so far since then. Everything seem to be fine. They get used daily with no...
  22. S

    hs3540 wire shearing prevention? VIDEO

    The other plug on your motor is for a sensored controller. With that hub you can use either controllers. Just leave it your hub will run fine. As for the plastic ring. Make your grove deeper so that the wire sits nicely at a 90 degree angle
  23. S

    building a 24s/11p 88.8V/59Ah lipo battery without welding

    Looks great!
  24. S

    Help: Anderson connector alternative?

    Jim Give me a call. We are the Canadian dealer for Anderson Connectors. We have less expensive tooling for them. We carry every color. We also have the high heat power poles. 905 831 5068. We are 15min east of Toronto
  25. S

    Will this battery configuration work?

    This looks fine. But do not parallel the two balance leads, also do not plug them into the Icharger balance board in that config. I allready blew my board up Thats my opinon. Any one else do this?
Back
Top