Search results

Date Relevance Most replies

  1. monie jacobsen

    Speed control with a potentiometer

    Hi fechter Thank you very much for responding to me;-) My located is Denmark... I'm cautious about buying if more defective BLDC Controller! Yours sincerely Monie
  2. monie jacobsen

    Speed control with a potentiometer

    Hi fechter "Maybe time for a new controller. Ones like that are pretty inexpensive." Yeah, you're right fechter ... Can you help me with another BLDC Controller, with the following technical data: 1: Max 48Volt 2: Ca. 300 - 500Watt 3: And with the possibility of using the potimeter;-) Yours...
  3. monie jacobsen

    Speed control with a potentiometer

    Hi, fechter Thank you very much for responding to me. Has test "S" (SV or ST?) ... But without result for speed regulation with potmeter. And one labeled with PWM with find square signal shown on oscilloscope! Motor runs at full speed, even though the throttle wires are not connected to...
  4. monie jacobsen

    Speed control with a potentiometer

    Hi, fechter I can not find the throttle signal that is marked "SP". Do you have another solitary place that can be used? Yours sincerely Monie
  5. monie jacobsen

    Speed control with a potentiometer

    Hi fechter Thank you very much for responding to me. Reply 1: Where does the the green wire from the hall connector attach on? Is connected to point "v" the board? 2: See pictures below of PCB layout: Hope you can use the above picture? Yours sincerely Monie
  6. monie jacobsen

    Speed control with a potentiometer

    Hi fechter Thank you very much for responding to me. I can not see where it goes wrong. But cable to the potmeter does not work! Have tried a lot with many options but without results. Yours sincerely Monie
  7. monie jacobsen

    Speed control with a potentiometer

    Hi,fechter OK, The picture is a little blurry. Will try with a better picture below! What location on PCB Layout should the center of the potimete be connected to Will you check this location? Thank you very much for your great patience with me and the problem;-) Yours sincerely Monie
  8. monie jacobsen

    Speed control with a potentiometer

    Hi, fechter Under PCB layout - red circle = "V" has direct connection to the green cable to the center of the potimeter! So the connection is OK! But the speed control system still does not work yet? Yours sincerely Monie
  9. monie jacobsen

    Speed control with a potentiometer

    HI Pfnyc Hi, thank you very much. But the type of controller I used is not the same type you use. But throttle wires colorcoder are not the same as you use. But it gives a good guide. Yours sincerely Monie
  10. monie jacobsen

    Speed control with a potentiometer

    Hello everyone Below you can see 3 pictures: Hope you can see something? But otherwise, I would like your help with another Speed control that can be used with a potentiometer. Do you want to go through a web link to your proposal for a speed control. Technical wishes: 48 Volt Just as small...
  11. monie jacobsen

    Speed control with a potentiometer

    Hi fechter With the green wire disconnected. Measured by the negative voltage of the battery between Green and gnd = + 5.14V Yours sincerely Monie
  12. monie jacobsen

    Speed control with a potentiometer

    fechter - if i disconnect the green wire it still runs at full speed yes :/
  13. monie jacobsen

    Speed control with a potentiometer

    To fechter Has a voltage adjustable on pot 0-5V. But Motor running is not regulated. Drive at full speed! Yours sincerely Monie
  14. monie jacobsen

    Speed control with a potentiometer

    Hi fechter and Glyn Have tried with all ground wire to connect same and lead them to ground (Gnd - Black). This did not solve the problem for a smoothly controlled speed. Here are the pictures below! Is there anyone who can help with a simple diagram for connecting to the potentiometer as...
  15. monie jacobsen

    Speed control with a potentiometer

    Hello everyone Is there anyone who can help with a simple diagram for connecting to the potentiometer as speed control for the device below ;-) Which cord color should be used...
  16. monie jacobsen

    Speed control with a potentiometer

    Hey fechter BLDC The motor is running now. (2856 omdr/min) constant! But the potentiometer does not regulate up or down? Can only adjust between 3.34 V to 4.98 V. Can not regulating with Pot? The green throttle wire goes to the middle leg on the 10k potentiometer. Are the 10k too small? I'm...
  17. monie jacobsen

    Speed control with a potentiometer

    Hello everyone It's this wire ON / OFF I'm looking for? Can not turn on the device to see the BLDC motor run. Would you be helpful? Yours sincerely Monie
  18. monie jacobsen

    Speed control with a potentiometer

    Hey fechter I just want to make sure! Is it the blue wire to be mounted in the middle of the 5K Potentiometer? Is not one of the wires with 5V source? Is there a wire that operates ON / OFF? Or are there other executives who should also be connected? Yours sincerely Monie
  19. monie jacobsen

    Speed control with a potentiometer

    Hello everyone Speed control with a potentiometer! Does anyone here have a suggestion how to control speed with a potmeter as below on the web link...
  20. monie jacobsen

    Halbach array Inrunner or Outrunner

    Hello Buk It is very nice that you look at the problem. Thank you very much for this! But I can only hope that anyone can come up with suggestions so my Inrunner 4-Pole and 6-Tooth can run. It will be very enjoyable. Have worked on the project for almost 2 years. Yours sincerely Monie
  21. monie jacobsen

    Halbach array Inrunner or Outrunner

    Hello Buk I am using YEP 120A Brushless ESC https://hobbyking.com/en_us/yep-120a-hv-4-14s-brushless-speed-controller-opto.html?___store=en_us And using the Arduino coder is attached below! Do you have a suggestion for the codes? You may want to correct the codes if you have a suggestion Yours...
  22. monie jacobsen

    Halbach array Inrunner or Outrunner

    Hello Has mounted Stator in Delta. Please see Delta Winding Configuration below. And with a compass under the stator, I could find that the winding was ok, by step numbers State 1 to State 6. So stator winding and connected in Delta finds I'm right. But the inrunner 4-pole rotor does not...
  23. monie jacobsen

    Halbach array Inrunner or Outrunner

    T0 Buk Thank you very much Buk I will immediately test your proposal. Comes back with report with BLDC Motor testing. Thank you very much for your suggestion.) Best Regard Monie
  24. monie jacobsen

    Halbach array Inrunner or Outrunner

    Hello everbardy How should I connect it Delta? Would you like to be helpful with a schematic drawing on how to connect the above-mentioned BLDC Motor. Would you like to be helpful with a drawing? Yours sincerely Monie
  25. monie jacobsen

    Halbach array Inrunner or Outrunner

    Hello Thank you very much for responding .. But I wish that someone will help a winding drawing for an Inrunner 4-Pole and 6-Tooth. Yours sincerely Monie
Back
Top