Search results

Date Relevance Most replies

  1. S

    Cycle Analyst - Solar Shunt Parameter

    ok, for my level of knowledge I will take the option to write to Grin :-) it will be easier for me :-) Thank you so much for the help
  2. S

    Cycle Analyst - Solar Shunt Parameter

    thank you :-) reading your message , I realize that I never saw a R value so I guess it is not a shunt looking at the picture here , I can only see +/- 16A https://ebikes.ca/solar-current-sense.html I was able to change the A/V scale value and it was better but as time went on, I had to...
  3. S

    Cycle Analyst - Solar Shunt Parameter

    I have my setup working great for the past 3 summer but this year, I had an electrical problem and my solar reading was all wrong, -1400 instead of the regular +300 Watts and it was very unstable. I repair the original electrical problem, but reading was still wrong, so I decide to buy another...
  4. S

    Fuse selection for custom eBike

    I found the problem. I had a master switch, and 1- Contact became loose inside, it started to heat 2- Vibration cause the wire to break a little
  5. S

    Fuse selection for custom eBike

    my knowledge is limited in this area. I was hoping to protect everything :-) where I worked, we had more of a programmed protection which could let pass high starting current but after that even a lower current would open the circuit. or a current level for a certain time and a higher lever for...
  6. S

    Fuse selection for custom eBike

    ok, now the link work :-) Thank you to increase my knowledge. I see this rated at 150 V DC. does that mean that voltage (tension ?) is less important as long as it is higher than the one on my electric circuit ?
  7. S

    Fuse selection for custom eBike

    ... if your batteries are in series. they are in parallel when I click your link, it goes to Buying again, but with not result ? maybe only you can see it.
  8. S

    Fuse selection for custom eBike

    you are completely right 1. yes it was the fuse holder that melted. where do I look for the one you talk about. and what amp do you think I should use. 2. one fuse per battery. originally I design this solar eBike to run in Asia where I knew I might spend days without seeing a person so I...
  9. S

    Fuse selection for custom eBike

    I'm no electrician :-) I have two motor attach to two 52 volt battery on my solar eBike. With both motor at maximum, I see around 2400 watts going out the battery. I found some fuse rated 40A at 58 Volt but so far I melted 2 of those, when I go at full speed for a while. Do you have advice...
  10. S

    eBike 2 motor with one regenerative

    Ohhh, do you think I could do it with my current Ezee motor I wanted to replace the Ezee with the GMac, but if I can do regen with the Ezee, that would be great. (I just realize that in my first post, there is an error I wrote I have two motor, a Bafang and an Ezee.I am looking to the the Ezee...
  11. S

    eBike 2 motor with one regenerative

    Wow that was fast :-) what do you mean by typical direct drive hub ?
  12. S

    eBike 2 motor with one regenerative

    I have two motor, a Bafang and an Ezee. I am looking to the the Ezee for this one with regenerative capacity https://www.ebikes.ca/product-info/gmac.html From what I understand, this emac motor could be my main way of breaking in my city ride. I switch between motor regularly during a ride...
  13. S

    Flexible solar panels on a bike frame

    I forgot to put a picture of his bike
  14. S

    Flexible solar panels on a bike frame

    angle between the sun and the panel is important mine are flat and early in the morning or late in the afternoon, I could get more power If I could incline the panel https://amaliasolar.wordpress.com/photo-video/ Justin fro eBikes.ca create one where the panel are on an Arc and he can change...
  15. S

    Max Amp and Watts on 12 gages 4 feet

    I don't go at 2200 watts very often :-) I now feel confident that the change from 10 to 12 won't impact much my setup. Thank you so much !
  16. S

    Bafang eBrake problem and maybe Cycle Analyst

    those are not the last one, there was a few change since then but you will get the idea :-) so far I have a lot of fun with it. https://amaliasolar.wordpress.com/photo-video/
  17. S

    Max Amp and Watts on 12 gages 4 feet

    I have two 52 Volts battery and 2 motors. if I used both motor at maximum capacity I consume about 2200 watts I was using 10 gages cabling but I had problem with my Anderson connector because the cable were too big to fit in the connector. I want to switch to 12 gage. I will have about 4-5...
  18. S

    Bafang eBrake problem and maybe Cycle Analyst

    The drawing not complete but the bike was great last year, and now I am doing some change to the wiring. I have two throttles, two batteries and two of all important part. The goal was to have redundancy for a trip in Asia I wanted to do but so far, I can't find a boat to ship with bike with...
  19. S

    Bafang eBrake problem and maybe Cycle Analyst

    Wow where did you get those drawing. very nice. yes, you are right the 5 volt is not in the ebrake but in the cycle analyst connector where the ebrake is connected I did not realize it until I read your answer. so I don't know if it is required :-) but because both Bafang and signal analyst...
  20. S

    Bafang eBrake problem and maybe Cycle Analyst

    I have two batteries in parallel. I use to have gage 10 but I had trouble with my Anderson connector and downgrade to 12 gage like the rest of my wiring.
  21. S

    Bafang eBrake problem and maybe Cycle Analyst

    my trike has a left and right brake only (no rear). usually I don't break on one side only but I could happen in the best world, each brake would cut both motor but for now if each lever stop on motor I would be happy. last summer, I had a short circuit in a cable on the Bafang which cause the...
  22. S

    Bafang eBrake problem and maybe Cycle Analyst

    I have 2 motors on my bike A Bafang with it's own controller and an Ezee with a Cycle Analyst. My problem is related to eBike signal. On the Bafang. I have a lot of difficulty to find a position to place the magnet in a way that it will get further from the detector when I press the Brake...
  23. S

    Cycle Analyst with 2 shunt with new firmware

    Hello teklektik my app is progressing even if I am a bad programmer :-) now I received data from cycle Analyst in a Arduino, send it through bluetooth, then I read the data stream and display it in big square on my iPhone. what I would like to add is to be able to ask the firmware version...
  24. S

    Cycle Analyst with 2 shunt with new firmware

    I just update my firmware to CA3-13v1S with the solar beta I received 20 data. I read in the eBikes Blog that you removed the GPS data in v1S. great because I don't have a GPS yet :-) (oh I could be using iPhone data) I am building (at least trying) an iPhone app combine with an Arduino board...
  25. S

    Cycle Analyst with 2 shunt with new firmware

    I was about to tell you that I received only 14 data separated by a \t and with end of line being a \r but I realize that in the CA I just bought I did not put the Solar Firmware... so my bad :-)
Back
Top