Search results

Date Relevance Most replies

  1. C

    TSDZ2 OSF for all displays, VLCD5-VLCD6-XH18, LCD3, 860C-850C-SW102.

    I have 860c display with last software on a tsdz2 motor. My voltage percentage in the upperleft of the display does not match the voltage of my battery. I know one is in percent and the other is in volt, but when i have 45 volts, i have 0 % on the display. My cut off voltage is 38 volts since...
  2. C

    TSDZ2 OSF for all displays, VLCD5-VLCD6-XH18, LCD3, 860C-850C-SW102.

    I have done some test, closed the display and waited few second, closed the battery switch. I have set a delay of one hour to reset the trip value and everything works now. I really did not know that i had to turn off the display first for the data to be save. Thank you for your advice.
  3. C

    TSDZ2 OSF for all displays, VLCD5-VLCD6-XH18, LCD3, 860C-850C-SW102.

    The reset happen randomly and i do not wait few second to close the battery switch. I can do some test, like close the battery switch few min. after i close the display and see what happen. Sometime i do not even close the display before i close the battery switch. Does the display itself, with...
  4. C

    TSDZ2 OSF for all displays, VLCD5-VLCD6-XH18, LCD3, 860C-850C-SW102.

    I have a 860c display with the newest version, sometimes the trip distance A or B are reset to 0 when i close the battery switch, when i reopen the battery switch after few second or minutes the trip distance is 0. I have programmed the reset to 8 hours, but to have the reset to work i have to...
  5. C

    TSDZ2 OSF for all displays, VLCD5-VLCD6-XH18, LCD3, 860C-850C-SW102.

    I use the throttle to give a faster and easier start at stop sign without having to lower the gear ratio. When i use the 300/20 in startup boost the bike kick forward for half a second when i open the display. To not have the kick forward i had to lower the value to 170/20. I tried the hybrid...
  6. C

    TSDZ2 OSF for all displays, VLCD5-VLCD6-XH18, LCD3, 860C-850C-SW102.

    You were right, i had the old version. I have no fault now with the updated version. I use the throttle to help when i start the bike, it works when the road is leveled but if i want to start at the bottom of a hill it does not. Is there a function in the display to raise the power applied to...
  7. C

    TSDZ2 OSF for all displays, VLCD5-VLCD6-XH18, LCD3, 860C-850C-SW102.

    Here is the photo.
  8. C

    TSDZ2 OSF for all displays, VLCD5-VLCD6-XH18, LCD3, 860C-850C-SW102.

    The value is 20.
  9. C

    TSDZ2 OSF for all displays, VLCD5-VLCD6-XH18, LCD3, 860C-850C-SW102.

    The 860c display is brand new and come from eco-cycles and was already programmed with 20.c4, after i have made calibration then the problem occured.
  10. C

    TSDZ2 OSF for all displays, VLCD5-VLCD6-XH18, LCD3, 860C-850C-SW102.

    Value 194 too. Is it a problem if i leave Calibration disable?
  11. C

    TSDZ2 OSF for all displays, VLCD5-VLCD6-XH18, LCD3, 860C-850C-SW102.

    Yes they are the same. Value 194 for adc offset.
  12. C

    TSDZ2 OSF for all displays, VLCD5-VLCD6-XH18, LCD3, 860C-850C-SW102.

    I have 860c display with 500 watt Tsdz2. I have the new osf installed 20.1.c4 The motor is responsive and works very well. If i enable "calibration" in the torque sensor section i have an error 2:torque fault. I have made the calibration for torque adc offset and torque adc max and entered...
  13. C

    New "TSDZ2 Torque Sensor Central Motor"

    I bought a tsdz2 recently and worry i won't be able to flash the controller if it is the V2 version. How can i see the osf version on that new motor?
Back
Top