Search results

Date Relevance Most replies

  1. Gray haired Aussie Bloke

    Firmware wont flash

    Yep I believe we have followed the wiki implicitly When My friend arrives shortly we'll persue the possibility of incorrect paths. Personally I don't believe the path is incorrect as when checking the installation in C drive after de compressing,all the files appear to be in the directory.
  2. Gray haired Aussie Bloke

    Firmware wont flash

    Guday OffgridDownunder, First of aal some typos in my post I'll get the assistance of my friend on Monday when he comes over so until then I'll do my best to answer your queries and fill you in on what I have done 1. Github down load:;GitHub - emmebrusa/TSDZ2-Smart-EBike-1: TSDZ2 Open Source...
  3. Gray haired Aussie Bloke

    Firmware wont flash

    Greetings. I have attempted to flash my 36V TSDZ2 with the Version for VLCD5-VLCD6-XH18 with Java configurator. Everything went ell until the till the end step with the Java configurator. On pressing the compile flash button a dialogue box came up stating the the "make" command was not...
  4. Gray haired Aussie Bloke

    Motor drive cuts out

    It's now 6pm with the battery now cool. Attached are photos of where I took the readings from last time but as is stated I didn't measure properly. The photos show the same voltage for each bank. There is also a photo of the voltage at the battery connector to the motor.
  5. Gray haired Aussie Bloke

    Motor drive cuts out

    Ummm, I charged the battery overnight and the charger light was green this afternoon at about 2.30pm when I unplugged it. The battery was slightly warm when I took it off charge, Will wait till later this arvo to check it out. Standby for the next chaper as I seek to discover what the challenge...
  6. Gray haired Aussie Bloke

    Motor drive cuts out

    Thanks for your input. I have a TSDZ2 mid mount motor. No, the battery hasn't been on charger for at least a week probably longer. The motor spins freely and the brakes aren't binding. There appears to be continuity in the torque sensor but it is not showing up in the hidden settings. I have...
  7. Gray haired Aussie Bloke

    Motor drive cuts out

    Ok all, Have checked out the battery voltages this morning. I am pleased to announce that all battery voltages are abopve the 37v range and are within .2v in variation so the battery is in great condition as far as I can tell which is a relief for me. So where do I look now. Thanks all.
  8. Gray haired Aussie Bloke

    Motor drive cuts out

    Hi there. Attached is photos of battery from each side. The top of the battery is the top of the photo as orientated on the downbar of the bike. I don't see ten groups of batteries. the way the cells are connected. Please advise where I am to take the voltage readings from. Thanks
  9. Gray haired Aussie Bloke

    Motor drive cuts out

    I will need guidance to fulfill this request. I have a multimeter so lead on and I will advise of my readings. Photos would be a great help. Thanks.
  10. Gray haired Aussie Bloke

    Motor drive cuts out

    Ok This reply is to all who responded. The system was installed on the bike in January 2021 on average I ride the bike every Monday and Friday for approx 50km a ride. There have been a couple of periods because of medical reason the bike wasn't ridden for 6 weeks or so. According tho the display...
  11. Gray haired Aussie Bloke

    Motor drive cuts out

    Wow just look at that. Goes to show that one must proofread the post before pressing the enter button. No the new controller didn't fix the problem hence this request. Thanks very much for bringing that to my attention. other readers are probably asking the same question:-((( Have amended the post
  12. Gray haired Aussie Bloke

    Motor drive cuts out

    I have a 36v TDSZ2 running of a 17AH battery on a roadbike . About January I replaced the controller as it had malfunctioned after about 13 mmonths All was ok until two weeks ago. I was pushing up a 10% hill when the motor ceased driving and the VLCD 5 display went blank. I attempted to turn on...
Back
Top