Search results

Date Relevance Most replies

  1. M

    New "TSDZ2 Torque Sensor Central Motor"

    Thanks
  2. M

    New "TSDZ2 Torque Sensor Central Motor"

    Reading the Wiki whilst mine is disassembled I thought I ought to check the PAS sensor but the controller unit seems to stuck in place solid. Is there a trick to releasing it?
  3. M

    New "TSDZ2 Torque Sensor Central Motor"

    Received my new torques sensor and the cabled part is of a different design Original As supplied (albeit without the springs - have raised the matter) Note only two springs are shown in the suppliers photo and the wire connection is through a deep plastic moulding. I'm assuming if it now is...
  4. M

    New "TSDZ2 Torque Sensor Central Motor"

    Thanks for the advice. One solution is to wrap some rubber (bits of old inner tube) around the frame at the appropriate location which aside from stopping the bracket/clamp biting into the frame also stops any creaking noises arising there. I do have a problem with those parts in that the...
  5. M

    New "TSDZ2 Torque Sensor Central Motor"

    Found a youtube video https://www.youtube.com/watch?v=-V3G0GSx4zg taking a completely different approach knocking the lot out from the rear which worked albeit probably potentially not too good for the health of the torque sensor. The only thing that seems looks faulty/seems odd is that only two...
  6. M

    New "TSDZ2 Torque Sensor Central Motor"

    Thanks - easing does not seem to be working :(
  7. M

    New "TSDZ2 Torque Sensor Central Motor"

    Stripping mine down to try to establish what the fault might me and I cannot get anything to budge having taken the circlips off Any suggestions would be appreciated. The o ring meanwhile has fallen off - presume it needs a new one, what size should I order?
  8. M

    New "TSDZ2 Torque Sensor Central Motor"

    Got it into maintenance mode but instead of any torque sensor readout it showed beneath the large r e the total mileage covered and the motor did work briefly. Restarted and now in maintenance mode four zeros (still with miles thereafter) and which never changed. Wondering if I have both a...
  9. M

    New "TSDZ2 Torque Sensor Central Motor"

    Thanks for the info re the maintenance section :thumb: Its not the magnet - speed display is working fine on the display currently. The SW102 did arrive but not the necessary cable :( Think I'll leave it till the weekend to investigate further.
  10. M

    New "TSDZ2 Torque Sensor Central Motor"

    Tried that but some reason it jumps back to the main display before reaching it. Have just been out on the bike and the motor occasionally kicked in. I have had problems with the VLCD5 with it not showing speed or battery level at times and wondering whether its a fault with that - have a SW102...
  11. M

    New "TSDZ2 Torque Sensor Central Motor"

    My TSDZ2 suddenly stopped assisting today - display okay working lights correctly but no assistance from the motor. Do I take it needs a new torque sensor or could it be something else?
  12. M

    SW102 micro usb port

    Oh! I was reading the technical specification document on it which refers to a "Micro USB serial communication port, convenient for maintenance purposes. Still awaiting delivery of mine.
  13. M

    SW102 micro usb port

    Anyone know if the SW102 display gives power out on the micro usb port - have a 6v directional indicator remote on the handlebars that uses a pair of CR2025s and wondering if I could wire it to the port instead.
  14. M

    New "TSDZ2 Torque Sensor Central Motor"

    My VLCD5 display played up today giving a speed of 0.0mph and an indication of :lowbatt: ; towards end of this mornings commute it did come to life. Back home this evening after powering it off and on a few times did started show accurate reading. It has been very cold recently and last night...
  15. M

    New "TSDZ2 Torque Sensor Central Motor"

    Surely that has too many teeth = the TSDZ2 wrench only has 8 teeth
  16. M

    New "TSDZ2 Torque Sensor Central Motor"

    Noticed my M33 wrench as supplied with the motor is becoming a bit worn; is there a better alternative?
  17. M

    New "TSDZ2 Torque Sensor Central Motor"

    Tried the next smaller wheel setting and it seems have fixed the overspeed displayed mph, 26 (inches) being the setting which is 660mm, i.e. a 700 wheel (622mm diameter) with an extra 38mm attributable to the tyres.
  18. M

    New "TSDZ2 Torque Sensor Central Motor"

    Not sure what the display was playing at yesterday as today the motor apparently did not shut off until 17.1mph so set it the first smaller wheel to a 700 and 15.7mph is the displayed speed at which the motor shuts off. Will try the next but odds on that being less than 15.5mph (25km/h)
  19. M

    New "TSDZ2 Torque Sensor Central Motor"

    I've looked at that thread a number of times and no step by step guide seems to spring out of it as I can see. Would be useful if there was a step by step youtube video. On the subject of the display with the stock firmware having incorrect mileage/speed I have found increasing the wheel size...
  20. M

    New "TSDZ2 Torque Sensor Central Motor"

    You could try a different setting, 700 wheels are 622mm diameter but the tyres will add to the diameter; for that reason most bike computers require the wheel circumference entering which for 700 wheels will range from 2070mm for a 18 tyre (659mm diameter) to 2268mm for a 47 tyre (722mm...
  21. M

    New "TSDZ2 Torque Sensor Central Motor"

    Got my double chainring fitted, the stripped crank came off when a faced with a brand new crank tool, now sure what it gripped onto as but must have been just enough thread to grip. Front derailleur fitted and working - slight chain rub on some chainring (38 and 48) 7 speed cartridge settings at...
  22. M

    New "TSDZ2 Torque Sensor Central Motor"

    Neither the one I got (too thick) or one like that (Not enough reach around the crank) worked. Thinking of riding a local circuit then goes downhill and back up without the bolt in armed with an allen key the thickness of the one that its too thick and checking as soon as the pedal starts to...
  23. M

    TSDZ2 with VLCD5 shutting off

    Check the connections in the cable twix motor and battery; if soldered it could be a dry joint, if by connectors are they firmly fitted together and the wires well secure.
  24. M

    New "TSDZ2 Torque Sensor Central Motor"

    Thanks Picked up a gear puller from local car/bike shop but its too thick to fit between the crank and chainring guard so will try trimming it although I suspect that may weaken it too much. Have noticed this one https://www.amazon.com/Custom-Accessories-78886-Puller-Spread/dp/B000FK5IBG which...
  25. M

    New "TSDZ2 Torque Sensor Central Motor"

    Grand idea today was to fit the new chainring combo so crank puller tightened in place and then the releasing bolt turned and the puller came back out of the crank, the crank completely dethreaded :evil: Anyone any ideas of how to get the crank off? Have the stock chainring with solid...
Back
Top