Search results

Date Relevance Most replies

  1. B

    TSDZ2 OSF for all displays, VLCD5-VLCD6-XH18, LCD3, 860C-850C-SW102.

    Ok thank you for the help I have figured out the situation. I indeed have successfully flashed the motor and firmware is working as expected. I began to debug the temperature sensor and have determined that I had purchased counterfeit LM35 sensors. I purchased from ebay because could not find...
  2. B

    TSDZ2 OSF for all displays, VLCD5-VLCD6-XH18, LCD3, 860C-850C-SW102.

    Thank you for the assistance. I have read the manual thoroughly. I have already set the settings changing temperature to Slot one with value 0. I set limit of # of data to show to 1 so that only temperature should be showing. I set the length of time to appear to 0 so that it is continuously...
  3. B

    TSDZ2 OSF for all displays, VLCD5-VLCD6-XH18, LCD3, 860C-850C-SW102.

    Actually upon relooking I do not see 99.9 on startup. I did see that the first time but my battery was fully charged. I think it is showing battery %. Now it is showing 95.7 on startup. I reflashed with "set parameters on startup" and dont see any apparent changes. Pressing lights on results...
  4. B

    TSDZ2 OSF for all displays, VLCD5-VLCD6-XH18, LCD3, 860C-850C-SW102.

    If i switch on the lights it will cycle between the same 3 values, although i set in the configurer to only show one value permanently (length of 0). Also holding minus for 3 seconds doesnt give any indication that walk mode is active. Is there a UI indicator that walk mode is happening? (I dont...
  5. B

    TSDZ2 OSF for all displays, VLCD5-VLCD6-XH18, LCD3, 860C-850C-SW102.

    Hello, I am having trouble flashing the firmware onto the device. For reference I am using VLCD5 I attempted to flash the tsdz2 using the java configurer, seemed to work perfectly, cmd closed out of itself, no hanging around error message. But when I plug in the battery and turn on the screen I...
  6. B

    Tsdz2 firmware open source adapted to vlcd5, vlcd6 and xh18

    Hello, I am having trouble flashing the firmware onto the device. For reference I am using VLCD5 I attempted to flash the tsdz2 using the java configurer, seemed to work perfectly, cmd closed out of itself, no hanging around error message. But when I plug in the battery and turn on the screen I...
  7. B

    New "TSDZ2 Torque Sensor Central Motor"

    Well I have already built half the easyDIY display (btw it is not easy haha) :oops: . Casainho should update readme wiki to state that project is abandoned. It had a lot of cool improvements on there like heat sensor and such. Could I still continue with the old Casainho firmware or many...
  8. B

    New "TSDZ2 Torque Sensor Central Motor"

    Hello friends. I like this project but I am quite confused by the organization of the project. It is highly fragmented. I have gotten all the parts and started to build the casainho display. Is this the correct route? I am confused which motor firmware goes along with this display. I am using...
  9. B

    EasyDIY OpenSource display for EVs: TSDZ2 and Bafang M500/M600 EBike motors

    Hello friends. I have a breakthrough for the STLinkV2 firmware issue. PROBLEM: The safety bit is set on newer versions of the NRF52 board and command nrf52_recover is not available in this state. Some have recommended J-link but this is not required as long as you have a newer version (J24 ) of...
Back
Top