Namejs
1 µW
Hello everyone
It's been in my head for a while to convert ICE vehicle to EV. I'm into motorcycles yet a full sized bike conversion would cost upwards of 2000-3000gbp and legal mess so I choose a smaller version aka mini moto.
Part list:
Electronics
Motor: Sensored C80100 130kw 7kw
http://alienpowersystem.com/shop/br...nsored-outrunner-brushless-motor-130kv-7000w/
I haven't deeply researched about motors, but those 7kw probably aren't continues , correct me please.
Esc: 300A 4-24S Evolution 3 ESC HV-Sensored
http://alienpowersystem.com/shop/esc/alien-300a-4-24s-evolution-3-esc-hv-sensored/
My concerns are that this might be too powerful for the motor and would burn phase wires. I've looked at 200A esc ,but as motor max amps are 200 I doubt esc could provide them for some short bursts. didn't see any 250A esc for that reason.
Batteries: Turnigy Graphene 4000mAh 6S 65C
https://hobbyking.com/en_us/graphene-4000mah-6s-65c-w-xt90.html
Going to wire them in series of 3 with the 300A esc, that should be plenty enough.
Sprockets, chain & misc
Rear wheel currently has 70 tooth sprocket 6mm pitch and ? size sprocket on engine.
My doubts are that torque on the motor will slip through sprockets.
Planning to go onto 8mm pitch with a sprockets ratio of 74/17, would it be enough? With this setup I should reach theoretical speed of 22.2mph at 3000rpm or max speed of 48mph at 6500rmp.
I still have to sort out the rear end, rear spindle thread is rounded, have to get new chain tensioners, spacers, etc.
I will be adding mechanical brakes with electrical "feedback/cut off?" I've got hard time understanding how to deal with this.
Total estimated costs
650-750 gbp
It's been in my head for a while to convert ICE vehicle to EV. I'm into motorcycles yet a full sized bike conversion would cost upwards of 2000-3000gbp and legal mess so I choose a smaller version aka mini moto.
Part list:
Electronics
Motor: Sensored C80100 130kw 7kw
http://alienpowersystem.com/shop/br...nsored-outrunner-brushless-motor-130kv-7000w/
I haven't deeply researched about motors, but those 7kw probably aren't continues , correct me please.
Esc: 300A 4-24S Evolution 3 ESC HV-Sensored
http://alienpowersystem.com/shop/esc/alien-300a-4-24s-evolution-3-esc-hv-sensored/
My concerns are that this might be too powerful for the motor and would burn phase wires. I've looked at 200A esc ,but as motor max amps are 200 I doubt esc could provide them for some short bursts. didn't see any 250A esc for that reason.
Batteries: Turnigy Graphene 4000mAh 6S 65C
https://hobbyking.com/en_us/graphene-4000mah-6s-65c-w-xt90.html
Going to wire them in series of 3 with the 300A esc, that should be plenty enough.
Sprockets, chain & misc
Rear wheel currently has 70 tooth sprocket 6mm pitch and ? size sprocket on engine.
My doubts are that torque on the motor will slip through sprockets.
Planning to go onto 8mm pitch with a sprockets ratio of 74/17, would it be enough? With this setup I should reach theoretical speed of 22.2mph at 3000rpm or max speed of 48mph at 6500rmp.
I still have to sort out the rear end, rear spindle thread is rounded, have to get new chain tensioners, spacers, etc.
I will be adding mechanical brakes with electrical "feedback/cut off?" I've got hard time understanding how to deal with this.
Total estimated costs
650-750 gbp