I have a 18 x 4115 MOSFET 84-132V Real Highway Speed Controller and I am going to use it with a lithium 88.8V 50A rate battery. This controller's information reads that 45A is the current rate (for higher current, you may need to beef up the trace, shunt, and reprogram it via the software.)...
Ya, another issue I have is there is a gap from my front hub to my fork. I have DMR 20mm hub on the 20mm spindle on fork. The hub slides in the fork spindle. I want to stabilize the hub from sliding side to side. How do I resolve that?
Thanks, I found a brake adapter that I think will work. Thanks again for helping resolve the set backs in my bike upgrade. Will post my upgrade progress soon!
Thanks, but when i call up the fork company they won't talk to me unless I am a bike shop. SOO, frustrating! I can't take my bike into the bike shop becuase I have it halfed wired up but need it to work correctly as in roll and brake effectively for me to finish wiring it. I'm in a mess!
I ran into a few issues on my bike upgrade that I don’t understand how to resolve. One issue is that the front brakes don’t match up to the forks. I bought hydraulic 203 front and rear brakes. It seems as though the brake attachment on my new forks is in a different place on the fork than the...
I am installing the comotor and the axle is to large for my torque arm. What torque arms will fit the axle. Can I change the insert on the torque arm I have now?
Thanks for the info. I just bought a a set of nice 110mm spacing forks - RockShox Domain RC Dual Crown Coil 200 Maxle 20 Black. This fork will make the bike look much better too, plus my new hub will fit! I hope the hub will fit. It should right?
This is the one I just bought. This fork...
I bought a DMR 20mm hub for my front wheel and I was expecting to be able to lace it up in my front wheel with 13g spokes and have it trued and be set. The hub comes to me with no skewer for me to be able to fasten to my front forks. I took it to a bike shop and was told that the hole is large...
I bought a Cromo hubzilla and ordered a 13t freewheel but it is too small. Would someone please tell me what size freewheel I need that will fit on this hubmotor?
Thanks,
Jason
Thanks for the feed back cuz I asked the question about crank length becuase I thought there might be a standard crank length that people were using on a 26" frame with 21" tires. I guess I can measure the the ground clearance when I finish putting the bike together. I was hoping that there...
I just bought 16" rims with Michelin M29s 16x2.75 tires. My bike has a 26" frame (EW-400). I was wondering what size cranks most people use to conpensate for ground clearance? I want to be pedaling a little as well when I am using the electric motor. I know the difference between 170mm and...
I am going to put 2.25" moped tires on 17" moped rims on the front and rear on my 26" bike. The Shinko tires weight 3½ lbs, and the unmounted diameter is approx. 21¼". I was thinking power-to-weight ratio is why I selected 2.25" tire. Should I get a bigger tire such as 2.50 or 2.75? What...
Wow, a lot a responses. I thought I would run it with this stock hub motor and get a hubzilla if it will work on Lyen's 4115 18FET controller. I do have a racer hub motor but Lyen said that his controller is not a good match. Should I just order a hubzilla now...
I have an Electric Wheel 400 bike (EW-400) http://high5scooters.com/productinfo/ew400.htm. I am upgrading my electric bike and I removed the stock controller and connected my stock 36v lithium battery in series to another 51.8v lithium battery...