Recent content by GianlucaO

Ciao a tutti. Sto cercando di configurare il mio motore QS 138 90H con il controller ASI BAC4000, ma non ho le impostazioni. Nell'app Kilowatt devo inserire queste impostazioni, ma quelle con l'asterisco non so cosa siano o cosa scegliere. Qualcuno sa come aiutarmi? Vorrei anche sapere come...

Hello everyone. I am trying to set up my QS 138 90H motor with the ASI BAC4000 controller but I don't have the settings. In the Kilowatt app I have to enter these settings but those with the asterisk I don't know what they are or what to choose. Does anyone know how to help me? I would also like...

I charged the battery to the max 83.9v and now it works. Now the problem is to find all the settings for my QS 138 90H engine. Are they available?

Help with ASI bac 4000. I connect the battery (72v) and wait to precharger with resistor 250ohm. Arrive at max 25v. Also with direct wire. When i turn ok Key (PIN 9) the tension go to 0v. Can you help me? Thanks I am the unluckiest person in the world

I bought an ASI bac4000 because mine died. It was mounted on a Talaria. Do you know what the settings are for the engine I use QS 138 90H?

I bought an ASI bac4000 because mine died. It was mounted on a Talaria. Do you know what the settings are for the engine I use QS 138 90H?

No, it reads about 19ohm and it is shorted to ground (multimeter beeps). So I will have to disconnect all the 5v components? Could this thing have damaged other things like bluetooth module or other 5v powered? I am seriously worried.

Yes, disconnected cables. Yes the wiring was poorly produced by the supplier. The display is always produced by him I don't know if it has a brand, at startup it shows the Bull Bike logo of the seller.

hi, the problem of my asi bac8000 is on the 5v line (pin 4 and 8), short with gnd. so i will have to have it repaired. what could be broken inside? do you know what is the electronic part or component that manages +5v? for the short time it worked the display showed a "throttle voltage out of...

hi, the problem of my asi bac8000 is on the 5v line (pin 4 and 8), short with gnd. so i will have to have it repaired. what could be broken inside? do you know what is the electronic part or component that manages +5v? for the short time it worked the display showed a "throttle voltage out of...

There is a GND ground (PIN 15 of controller) to the display, two 12v PINs (PIN 16 of controller), TTL RX (PIN 13 of controller) and TTL TX (PIN 3 of controller). The problem in my opinion is the wiring to the Throttle connector and Brake connectors.

Hi, I bought an ASI bac8000 complete with wiring and display some time ago. I mounted everything but there is no response from the accelerator and the red LED was flashing. Now the display and the red LED do not light up anymore. I found the PIN out of the controller and with a multimeter I...

I contacted the seller because now I think the wiring he provided me was wired badly. looking at the controller pinout I find myself in this situation now (I think the wiring is wrong and I hope the controller is not damaged too 😞): P.s. the numbers of the PINs writed near connectors are of the...

Wiring harness (6p + 16P): https://store.bull-bikes.si/en/home/38-sur-ron-wiring-harness-basic.html With 16P i can connect throttle (3 pin) , brake (x2), ignition and Display (5PIN) and a Red wire to B+ on controller with fuse. Now i'm discharging the battery using a DC-DC 72v to 12v with a 12v...