Recent content by osa57

Hi, thanks a lot for this tip! I couldn't understand why at 0,4V Regen kicks in but at 0,35 there is NO Regen at all. So I followed your instruction, it works perfectly now! Regards

I have solved this issue by following the technical guidelines on this document Basically it is necessary to shunt the Throttle and the EBrake entries on the Higo 9 connector. Now regen works like a charm!

I have already used 9Continent RH212 hub motors with Phaserunner and everything was always fine, regen did work immediately well. Now I have a Baserunner (no Phaserunner are available...) and this is my setup: - 48V battery - RH212 9C hub motor - L10 Baserunner From the Phaserunner suite this...

Hi there, is there a way we can see the Charge Graph from the Satiator on a connected PC? It would be very interesting in this scenario where I am trying to see the relationship between the amount of charged Wh and my battery SoC. thanks for your help!

Hi, Concerning this subject, here I would like to bring some concrete results of real life tests on a more specific point: Is there any relationship between: - amount of energy recuperated by regenerative braking - speed of the bike in the descente In order to discuss above relationship I...

Hi, I have a Falco hub motor, with internal width between flanges of 13mm (see picture) Would this be enough to install the HubSink? Thanks! https://drive.google.com/file/d/1azY5SJ-YN4XkUpxtfP8uZTTktL1Kzrqa/view?usp=sharing

Hi, I didn't connect the 'battery state pins' to the battery case. It was too difficult for me with my tools 😙 Of course now I don't see the LEDs on the battery case about it's charge status. But from my Cycle Analyst I get very reliable information. And when I charge the battery, the different...

I have built a recumbent bike with front geared hub motor, 36V battery, 150W solar panel :D Last summer I participated to the Sun Trip rally across France, Italy and Switzerland, I was able to get to the finish but I also learnt a lot...

Yes, I am using 2 LIPO's 8S (5800 mAh each) on a Panasonic 26V ebike. Please note that since I am NOT using the original BMS I have installed a Cycle Analyst to monitor the battery discharge. You can also check some more details here: 5Y5ycw5jNUU

After 3 years and almost 10000 km, both my 5800 mAh Zippy batteries are still in excellent shape :D Every time I recharge them, they are (almost) perfectly balanced. I normally charge them in parallel, so the complete recharge ( having set the Lipo charger at 10Ah) takes one hour at most. I...

Great post...... thanks Xenodius! I fully support your 'statement of directions' 8) Personally I have the same vision for everything you mentioned with just one exception. I don't want several KWh on board, not enough 'sporty' for me. The beauty of this solution should be of course 'long...

Hi, I finally received the 8S Zippy LiPo battery from HobbyKing :D 1) I first tried to use on the Panasonic with the Voltage it was shipped: 30.7 No problems, the Panasonic engine was running fine, punchy, and with almost no Voltage sag :mrgreen: 2)Then I charged the LiPo at 32 V: even in...

Hi, quick update on my last trip with following statistics: - total distance 260 km - duration 9 hrs 30' - avg speed = 27,36 - intial Voltage 29.2, final 26.1 - mAh used: 7700 - peak 'instantaneous' watts = 350 - total W/h = 200 - average W/h-Km = 0.77 - altitude gain 1950 m. I had a nice...

I didn't connect the new 7S Zippy with the old Panasonic balance plugs...this is why the BMS doesn't recognize them 8) Too much work and what about the old Panasonic battery then ? I still use it as a back up... So I am not too worried about the fact that I cannot charge the new Zippy with...

hi, excellent thread! I would like to bring also some 'european' point of view :) Recumbent bikes are created to be MUCH more efficient that normal bikes, so I think this is an excellent starting point! My project is to add to a recumbent bike (Nazca Gaucho High racer) a mid drive (Cyclone...