Recent content by Sattva Ram

What's the max amp for the 200 sp/2? Does anyone run it at 350 line current?

Can anyone help where to place the halls for such a motor? I tried the mercedes but it's awful. My guess is tho that it should be placed 40 mech degrees apart that is every 3 slots because the my 1020 also uses 40 mechanical degrees spacing for the 6 pole motor. Am i figuring it well?

Does anyone know where i can get the votol blutooth app for android?

Most definitely it seems i just blew mine for a too strong a regen. Overvolt minus 4ish volts is the regen protect btw. I set mine to 87 and as soon as i gave it 50% regen the fet blew. It's not that the regen protect wasnt working but i guess one friggin cell reached high protect before the...

Does anyone know what this 72900 em 260 is? It says 900 phase while with the other 260s it says 770 phase but the line current is 450 for both of them. Is it some sorta scam or these are truly different models? The 72900 is also more expensive. If the 72900 really could do the 900 phase it would...

I cant change some values on the far driver like pole pair or ratios in speed. If i want to crank up ratios in speed it says enter new BLE but it let's it set it downwards. What the hell can this be?

Mine is mid motor it's scorching heat here yet i couldnt bring the motor above 90 degrees even racing up a hill. My phase wires are also thick af due to the no lack of space. The far driver got a bit hotter tho than before but i guess it's to be expected i think it'll require placing it against...

You were right man i cranked it up to 100% all the way to 4000 and it's wicked...now it does what it should fkin wheelspin above 40 kph...i'll crank it up to 100% all the way save the last 3 ratios. I suggest you too crank it up better. Now i see what the problem was there was simply no phase...

Well it's funny becaise the jitter is very occcasional maybe one out of 50 start is jittery and even the extent of it varies. I think you have to "find" the perfect storm in terms of rpm and throttle position for it to do it. But it definitely appeared after 16 AN set. Top speed is kinda...

Well the problem is that you hardly use any FW. Your list ends around the start of FW border (which is good btw hubs dont like fw too much). But the problem is that my party with the V magnets starts where your ends. If i compare my sub FW numbers they are very similar to yours. So i dont think...

Yours isnt entirely dissimilar to mine but mine is definitely more tapery...i'll give it a shot tomorrow...what's your pole pair so i can convert it to mid motor to copy your setup...

20s. I was just messing with a low volt pack and left the 40 volt in...okay i try some 100% values but i'm a bit afraid lest the controller burns. I dont really get this ratios in speed stuff...it seems to me that it's only field weakening current. So it's not like i have 60% amps at only...

Thank you guys very good points. I let the autolearn do everything i also asked sia about the ratios in speed and they said it should taper. It seems auto learn is not doing much it's full of mistakes. Before i bought i asked them to set it up for the 138 but they shooed me away that auto learn...

I took it for a spin in high gear everything cranked up to the max AN set to 16 SOC 60. No real difference 290 max (tho according to the ANT bms which might even be too generous). I'll try the boost too maybe in boost mode it lets full power but i doubt it. It seems this is the max this...

The KI KP seems fine but even with that i might try 4 4 6 and 40 40 60. After all the 138 90h aint no small motor. Anyone maybe has a bulletproof setup for the 138 by chance? I'd appreciate that so i wouldnt have to experiment at the peril of a blown controller...