Search results

Date Relevance Most replies

  1. J

    Cycle Analyst V3 preview and first beta release

    thanks for explanation, I will listen to your presentation I have a modified "smartbms" from bmsbattery; There are 2 separated connection for controller and charger, so no interruption of the regen current is possible but discharge can be interrupted just after up to now I didn't have tripping...
  2. J

    Cycle Analyst V3 preview and first beta release

    Hi teklektik, thanks for your time ! that why I didn't find it ! do you agree it's a good idea to put in the battery setting ? I use a phaserunner, so it is possible to adjust it in the controller setting, but this setting need to be adapted at each battery change.
  3. J

    Cycle Analyst V3 preview and first beta release

    hello sorry if these thing has been already talked, this thread is too long for me. I just install the last 1.54 CA utility and last parameter CA3-1b21 I was looking to adjust the max regen current without success. is there a trick somewhere ? if not: ask new feature: max regen current (and max...
  4. J

    Cycle Analyst V3 preview and first beta release

    super teklektik ! this is a B Constant 4050K I read max 4000K earlyer in this post ?!
  5. J

    Cycle Analyst V3 preview and first beta release

    no advantage, but it more easy to find, just took it from an old board I didn't find ntc 10k 3950 on here ebay
  6. J

    Cycle Analyst V3 preview and first beta release

    Thanks teklektik Is it a chance that new release will support linear NTC in future ? or do I have to replace my calibrated sensor from my motor in this case, which sensor is the best ?
  7. J

    Cycle Analyst V3 preview and first beta release

    no idea ? I want to use a linear temperature sensor (diode) but with negative coefficient ! is it possible ? how ?
  8. J

    Cycle Analyst V3 preview and first beta release

    hello I try to add a diode (b-e junction of a si transistor) as temperature sensor on CAV3 p10 connected to CA, with 0 degre, I read 0.76V; with 100° I read 0.63v so If I understand correctly, I have a degre/v of 100/(0.63-0.76) => -0.769V if I enter 0.76 in 0 deg and 0.769 in T scale, the...
  9. J

    Cycle Analyst V3 preview and first beta release

    the setup utility 1.2 still not work for me. to have the good com port listed, I have to unplug CA and refresh. when read from CA, still same popups : first choose version V3 and after reading: "4 setting were expected to be found in this setup...." then most of the value in application doesn't...
  10. J

    Cycle Analyst V3 preview and first beta release

    Justin, your new upgrade utility v1.2 seem to work; native serial port and usb serial port present in combo box rem: my old totalcommander unzip program doesn't work with this format, I had to use 7z. I had also problem with setup utility 1.2 downloaded on 22/5 most of parameter received from...
  11. J

    Cycle Analyst V3 preview and first beta release

    I spend few hour to try to flash CA V3 prelim5 I have original cable, already use to upgrade one time with the new upgrade tools V1.1 downloaded today from ebike.ca (http://www.ebikes.ca/downloads/CA_Update_Tool_V1.1.zip) the serial connection combo box is empty with my previous download V1.1...
  12. J

    Any throttles compatible with rapidfire or trigger shifters?

    I use shimano dual control because it compatible with standard throttle...
  13. J

    Even Newer 4 to 24-cell Battery Management System (BMS)

    well, the previous test was done with all the cell connected in normal condition. the thyristor doesn't trig. If I bypass the mosfet to increase the current, the trigger is ok. so I thing there is a problem with the current too loo. is it an easy way to I increase a little bit the throttling...
  14. J

    Even Newer 4 to 24-cell Battery Management System (BMS)

    hi fechter thanks for your reply I have made some progress but still not 100% working I have replaced the 2A fuse on each cell balance wire by a 20A because the previous one was too inductive. there was also some acoustic noise coming out when balancing. I have also added a 100nf between input...
  15. J

    Even Newer 4 to 24-cell Battery Management System (BMS)

    hello, I have just finish a 20s bms (v2.4) but I have some problem with it: when I test it with a 3.6v ps, all the module seem to work correctly (no current below or at 3.6, current upper or at 3.65) connected to the batteries pack, the charge and balance seem also ok. all led will go on. but...
  16. J

    ecrazyman XJC8b116 72V 45A new controleur defect

    thanks Knuckles, Good idee to have a spare controller because I want to make some adaptation and a mistake can happen quickly. I wanted to add a pot to decrease the current limiting easily when ridding for long trip. I have read somewhere here (?) there is one resistor to adapt. but I need...
  17. J

    ecrazyman XJC8b116 72V 45A new controleur defect

    hello Keywin, thanks for your quick reply, I will be happy with a new controleur. I will let know here when received. thank again JC
  18. J

    ecrazyman XJC8b116 72V 45A new controleur defect

    I just received after 1 month a new controler. I decide to open it before putting on ebike. surprise: 1 capacitor is already explosed. :evil: why ? this is an 63v instead of an 100V. let be positive: they haved tested it before sending :P I cannot believed that an electrolytique capacitor...
  19. J

    e-crazyman new XJC8B116 controller

    oops I saw this thread before without notice the new processor :oops: thanks
  20. J

    e-crazyman new XJC8B116 controller

    info from keywin: The 72v/45A controller is available now ,but it is not use old infineon XC846 MCU , the new MCU is XJC8B116 ,The controller is hard start and use IRFB4310 mosfets ,thank you. this chips feature stronger than Infineon XC846. 1/ is a regenerative controller (with throttle)...
  21. J

    dewalt charger error but pack seem ok

    salut tu avais raison, c'etait bien le BMS. j'ai raccordé chaque cellule en parralleles sur les 2 batteries (en conservant les 2 bms) j'ai toujours un bms qui recharge et l'autre pas. je vais laisser cela comme ca, c'etait quand meme le but de mettre les batteries en parrallele et maintenant...
  22. J

    dewalt charger error but pack seem ok

    bonjour doc I'm pretty sure that I have respected the sequence I have unpack the box, then I have removed de 2 side support and fixed it with a tape away from cell then I have replaced the cell. ( I have solder the new cell with a standart Iron quicky) then connected again the 2 side support...
  23. J

    dewalt charger error but pack seem ok

    hello I have replaced a cell in my 36v a123 pack. the BMS seem to work, I can drain 9A on bms protected output (with the voltage divider schematics connected) when I put in the charger, the 3 led start bling after few second ! all cell voltage are about 3.3v... the charger work ok with another...
Back
Top