Search results

Date Relevance Most replies

  1. M

    Hall sensor installation placement and fitment problems

    Any imput?
  2. M

    Hall sensor installation placement and fitment problems

    I found this page in wich someone installed a hall like this.... i found no part or sensor number so i do not know what model it is... Mine is an a3144 hall sensor.... sorry for the mutiple posts i am just updating as i find info.
  3. M

    Hall sensor installation placement and fitment problems

    I found a sensor thats name is cysj166a that is 1.5x1.5x.6mm case sive wich i believe i would be able to get to work. Do you all think this woulf be combatable with a vesc?? Also would i power it the same??
  4. M

    Hall sensor installation placement and fitment problems

    Thanks for the reply... i wenr theough it a few times allor seemsed to be on the outside or between the teeth. I would like to keep them on the inside this tike around as all my externals werent very good.... any advise on it the above would work or if i can get 1mm wide or close hall sensors...
  5. M

    Hall sensor installation placement and fitment problems

    Hello all i recently recieved the motors that i will be using on my build. However i have come across a problem where the hall sensors will not fit between the stator teeth no matter how i try!!! Could i possibly mount the hall between the teeth but at the bottom of the stator off the bottom...
  6. M

    hub motor delta to wye conversion power consumption changes

    Fantastic this is just the answer i was looking for. Thank you very much for the explanation. My top speed is only going to be 35mph and i usually cruise at 15 or so. So higher end torque is not as important for me as start up torque I believe with this configuration paired with hall sensors...
  7. M

    hub motor delta to wye conversion power consumption changes

    I found a little bit of info on http://www.recumbents.com/wisil/e-bent/ ... torial.htm . it was a little bland but it seems to hold some truth. These need to be arranged one of two ways, "Delta" or "Wye". Generally Wye (also called "star") is more efficient. Wye has 1.73 times less KV than...
  8. M

    Adding hall sensors to outrunners

    continue as normal i apologize :wink:
  9. M

    hub motor delta to wye conversion power consumption changes

    ok so if i rewire it from delta to wye and im getting say 20 miles out of my pack(6s 2p) in delta will i now get 10 miles out of my pack in wye since i will be cutting my existing pack in half and running (12s 1p) will i then get 10 miles as a result? or will i get the same 20 miles ? to me...
  10. M

    hub motor delta to wye conversion power consumption changes

    Ok so if the original voltage is 6s and it consumes 30amps max at 6s in delta. And i re terminate from delta to wye what would the new power demands be since i only want it to rotate at 1.73 less than the original speed? Wouldnt going from such a high kv to almost hakf the kv and keeping the...
  11. M

    Adding hall sensors to outrunners

    sorry for hijacing i started my own thread that may clear a few things up. thank you all!! https://endless-sphere.com/forums/viewtopic.php?f=30&t=82545
  12. M

    hub motor delta to wye conversion power consumption changes

    Hello all I figure now is a good time for me to post a few questions and get some confirmation from the pros befor i make any fatile mistakes with my very expensive motors... I am currently building an electric mountainboard (5th one) this one however will use diy hub motors... mechanically i...
  13. M

    Adding hall sensors to outrunners

    this will be a hub motor
  14. M

    Adding hall sensors to outrunners

    i apologize for the second post i have another question i hope you all can help with... my motor is 135kv u8 motor i am going to wire it wye and get around 70ish to 80ish kv however is this going to change the amount of voltage this motor is going to require to pull the amount of amps it was...
  15. M

    Adding hall sensors to outrunners

    awsome!! thank you very much for your assistance it is very much appreciated. do you happen to have a schematic on how i should wire the hall?
  16. M

    Adding hall sensors to outrunners

    So as long as its 120 degrees apart it doesnt matter how many magnets there are roatating sround them?? Shoukd i be sure to place them between windings on the same phase or does it not matter so they could be between aa hall bb ??
  17. M

    Adding hall sensors to outrunners

    hello all I apologize for posting on an older thread however this thread is legendary and everyone on it is as well... well at least for me.. anyhow I have a question for the experts... i have a decent understanding of hall sensors and what now however I want you all to confirm my decision i...
  18. M

    elec tric mointianboard build

    Im trying to avoid tht way thanks for thr link any motor recommendations
  19. M

    elec tric mointianboard build

    Hey guys anyone.know of any good 600 kv or less sensored outrunner moters under 80 amps that can run on 4s. Bigger the better. Thanks. Also i have a turnigy sk3 350 Kv anyone know an easy way to.make it sensored tha.ks
Back
Top