Search results

Date Relevance Most replies

  1. D

    New lipos arrived today, but some aren't balancing correctly

    I have 16 4s 5000mah that I use. I did not buy them all at the same time. I think I bought 9 and then bought 7 a month or two later. I run 4 packs in series and 4 in parallel for 60ish volts and 20 amps. I have my Lyen set at 60 amps and 180 phase amps. I have seen 6100 Watts peak on the CA for...
  2. D

    Cell Pro Powerlab 6 help

    Ok I received the FET and installed it with no problems however the charger will not even turn on now. When I hook it up to the server power supply the power supply goes into protection mode, if I try to hook it up to my meanwell there is a spark and nothing else. I think I may be out of my...
  3. D

    A DIY Shop Tool for Making Torque Plates

    Nice! I like it alot! You may be able to make up the jigs and sell them.
  4. D

    Cell Pro Powerlab 6 help

    Got it thank you. PP sent.
  5. D

    Cell Pro Powerlab 6 help

    LOL. The charger is in a few pieces at the moment. Would you be interested in parting with any of the gets you have?
  6. D

    Cell Pro Powerlab 6 help

    My typical charge is 4s6p so I would think either would work?
  7. D

    Cell Pro Powerlab 6 help

    It is connected to the positive. At least I have continuity when I connect the fet with positive cable and a multi meter. I am fairly new to all of this electronics stuff but I'm learning quickly! When people mention drain I think of 1 1/2" copper tubing, solder and torches so this is a shift...
  8. D

    Cell Pro Powerlab 6 help

    More pictures. The fet is almost right behind the C19 marking.
  9. D

    Cell Pro Powerlab 6 help

    I did contact Revo and I believe they will probably take care of it. I use this everyday for my commuter set up so I can't really afford to have it down. If I can fix it quickly vs sending it in and taking weeks I would rather fix it. I will get pics of the whole board and post them up.
  10. D

    Cell Pro Powerlab 6 help

    Hello my e bike friends! I am hoping someone can help me track down a replacement part for my Powerlab 6. I was getting ready to charge my batteries like I've done several times and there was a pop from the charger and the magic smoke escaped. I tried to catch it to no avail. It will still power...
  11. D

    New Build Magic Pie2

    I haven't gotten a Cycle Analyst yet. I did buy a Turnigy Watt Meter but it arrived DOA!
  12. D

    New Build Magic Pie2

    I also made some torque arms up because my axle was trying to twist. It was trying to twist before I started my speed quest so I knew I better do something. CAD cardboard aided design
  13. D

    New Build Magic Pie2

    I forgot to mention my Voltz charger caught on fire so I ended up sending that back for a refund and I bought an FMA CellPro 6 which I like much better anyway. Moral is don't buy leftover, discounted chargers off of Amazon.
  14. D

    New Build Magic Pie2

    I opened up the motor and added some 10 gauge phase wires. And I drilled a few ventilation holes and programmed the controller for 50 amps continuous and 140 phase amps. Now I am cruising at 28-29 MPH. Still not fast enough so I guess I will be ordering 4 more Turnigy Hard Case 4s1p...
  15. D

    New Build Magic Pie2

    With the above set up I was cruising about 24-25 MPH on flat land with little to no wind. Up the bigger hills around here it would slow to about 22 mph without peddling. I rode back and forth to work (13 miles one way)like that until I decided I needed more power! I then did what any sane...
  16. D

    New Build Magic Pie2

    Good afternoon everyone I would like to thank Justin for saving this forum and I would like to thank all of the forum members for being here and posting up information! I started reading here a few months ago and ordered up a Magic Pie 2 kit from Gary at Golden Motor Canada for my Gary Fisher...
  17. D

    Bike not turning on. Seemingly ignoring battery input.

    On my Lyen controller there was an ignition wire (just a plain red wire by itself) that had to be hooked up to the battery. Perhaps your controller has an "ignition" wire?
  18. D

    Warning!!!**Do not buy Sabvoton Controller**!!!!!

    WOW I was going to buy one of these in the next week or two. Anybody have any tips on where to get a good sine wave controller? Or is sine wave not that important? Andy
Back
Top