Search results

Date Relevance Most replies

  1. SplatMatic69er

    Trying to flash bbshd firmware getting new eeprom message

    Seemed to have fixed itself. Now only random controllers won't take .bin file firmwares
  2. SplatMatic69er

    Trying to flash bbshd firmware getting new eeprom message

    I've updated the firmware of many bbshd controller's and today I went to open code file and was greeted by this message. "The file is over the validscope, and the exceeding part has been moved to EEPROM area" I also get this different variation; "The file is over the validscope, and the...
  3. SplatMatic69er

    CA v3 and Phaserunner settings-Throttle

    Bbshd pas is working with my phaserunner cycle analyst. Not sure why it didn't work for you
  4. SplatMatic69er

    Cycle Analyst shows completely wrong temp and powers motor without throttle input (partly solved)

    I'm having this exact issue right now. I have my throttle in set at 1v and throttle out min 1.1v. the motor spins up when turned on without throttle being used. It even does it with no throttle plugged in. Reading .84 with throttle plugged in, and .04 with throttle unplugged, causing motor to...
  5. SplatMatic69er

    ..

    ..
  6. SplatMatic69er

    Phaserunner L10 PAS wires + bbshd. 12v to 5v pad?

    http://www.endless-sphere.com/forums/viewtopic.php?p=571345#p571345
  7. SplatMatic69er

    Phaserunner L10 PAS wires + bbshd. 12v to 5v pad?

    Probably. Can you share the link to the thread? Might save someone some trouble if they come across this thread.
  8. SplatMatic69er

    Phaserunner L10 PAS wires + bbshd. 12v to 5v pad?

    I figured it out! Turns out you need to turn pas on in the cycle analyst setup program. Nowhere have I read from anyone that you must turn it on. I figured a step like that would be listed in a thread somewhere, but it's not! For the record; bafang mid-drive's require 5v. Cycle analyst provides...
  9. SplatMatic69er

    Grin Phase Runner / CA3 and BBSHD

    So it turns out you can't just wire up pas and have it work... You MUST turn pas 'on' in the cycle analyst setup program, otherwise it'll never work. Pas by default will not work with bbs motors unless pas settings are changed. Thank you to everyone for making me figure it out. In hindsight I...
  10. SplatMatic69er

    Having trouble removing bbs stator from shell

    I'm currently trying to perform a heat dissipation mod on my bbs02. I got the rotor out but I can't figure out how to remove the copper. Any advice would be greatly appreciated! Here is a picture from another thread of what I'm trying to accomplish...
  11. SplatMatic69er

    PAS Sensor compatible with Cycle Analyst

    I'm guessing the regulator I got from grin is broken. I'm not sure if it's required that I adjust pas pole count in the CA in order for it to read the pas sensor in the bbs02 but nothing I've come across has pointed to doing so. I'm very frustrated!!!
  12. SplatMatic69er

    PAS Sensor compatible with Cycle Analyst

    To troubleshoot the problem here instead of splitting threads.lol Sorry, I'm actively trying to troubleshoot this issue and also have like 5 endless sphere tabs open.. I guess I'm done troubleshooting for now because I don't know what else could be the issue. I did just confirm that the bbs02...
  13. SplatMatic69er

    PAS Sensor compatible with Cycle Analyst

    Yes, I would appreciate that as I made a mistake while posting. Didn't mean to split them.
  14. SplatMatic69er

    PAS Sensor compatible with Cycle Analyst

    I'm using the bbs02 pas sensor. From what I understand, the CA provides 10v and bbs02 needs 5v but now I'm unsure as it doesn't work.
  15. SplatMatic69er

    PAS Sensor compatible with Cycle Analyst

    Yeah I apologize for the less than stellar details. I thought I had it figured and then I didn't. I'm just overwhelmed at this point. Everything else wired up nicely, halls, phase wires... everything but pas. The pas plug coming from the CA has White/10v Black/ground Blue/direction Yellow/rpm...
  16. SplatMatic69er

    Phaserunner L10 PAS wires + bbshd. 12v to 5v pad?

    Interesting, I might try the 5v from PR. Not sure why pas isn't getting detected
  17. SplatMatic69er

    Phaserunner L10 PAS wires + bbshd. 12v to 5v pad?

    There was no red wire in the pas wire coming from CA pas cable, closest was yellow and I read a thread that said orange was the voltage so I wired yellow from CA to 12v end of pad. Perhaps because I soldered the leads to the bottom of the pad it isn't working
  18. SplatMatic69er

    Phaserunner not being read by PhaserunnerSuite

    Having the same issue with my recently purchased phaserunner & CA v3. Very disappointed. I downloaded the Phaserunner suit on my galaxy s9 and it just says not connected...now I'm having thoughts that I've made a mistake spending $590 on this hardware. What the heck? I'm using the programming...
  19. SplatMatic69er

    Phaserunner L10 PAS wires + bbshd. 12v to 5v pad?

    So I ended up finding the answer after digging 'endlessly' deeper into this platform. I can't quite remember what thread it was but it did say a step down is required for bafang mid-drive's. I emailed grin to confirm that I'll have to use a 12v to 5v pad and they confirmed it. When placing my...
  20. SplatMatic69er

    Phaserunner L10 PAS wires + bbshd. 12v to 5v pad?

    I downloaded the Phaserunner v6 manual and the v6 still requires pas to be wired up to the cycle analyst. I'm assuming (you know what happens when you assume) the PR v6 still requires a 12v to 5v pad/stepdown to be wired between pas and cycle analyst.
  21. SplatMatic69er

    Phaserunner L10 PAS wires + bbshd. 12v to 5v pad?

    Amberwolf are you the only person on this platform? You seem to be the only person to respond to my posts. Either way, I appreciate your responses. I was able to find a thread on here that was very helpful in showing how to wire the hall sensors and pas sensor wires...
  22. SplatMatic69er

    Phaserunner L10 PAS wires + bbshd. 12v to 5v pad?

    I guess I'm just dumb for asking such an easy question. The answer is probably staring me right in my face and I'm too dumb to realize it. I thought what better place to ask for advice about a phaserunner than endless sphere. They've had great topic conversations in the past that have really...
  23. SplatMatic69er

    Is there a way to fix a Luna ludicrous v1? No pas or throttle, clicking noise

    It was just a blown ludi v1. I had never broken a controller so I didn't know first hand how a blown controller acted. Thank you for helping me diagnose the issue, much appreciation.
  24. SplatMatic69er

    Phaserunner L10 PAS wires + bbshd. 12v to 5v pad?

    Hey folks, the phaserunner is back but only the L10. I had been planning on buying a frankenrunner Mt for sometime and figured out how to wire it all up but when I went to buy it I found out it's been discontinued in place of the phaserunner L10, they won't have the Mt version till end of summer...
  25. SplatMatic69er

    Gustavo chainring for Bafang mid drives

    How has it held up to this point? It's been about half a year, any updates to the wear and tear? Since there are no updates I'm guessing it's still performing well.
Back
Top