zeccato
100 W
- Joined
- Jan 17, 2019
- Messages
- 177
It seems to me that the pas can connect directly
to the control unit (true?) (to the 6-wire connector of the AC (or display) of the control unit,
(is in the middle see photo):
1 Battery Voltage Vcc-L (red
(I think it's battery indicator, my 48v., and I do not need to use it)
2 GND / Shunt + ve (black)
3 Shunt -ve / Shunt -ve (blue)
4 Shunt + ve / Shunt + ve (white)
5 Speed Signal / HE (yellow)
6 Throttle signal / SLA. (green)
So: where do I connect pas directly without the diplay and c.a.?
My pas is different, I have read that not all pas are compatible
with the control units, but I want to try,
but the display looks the same.
If the pas is connected directly, programmed to
30% does not work,
I should also connect the display, so: how do I connect display and pas?
Or display and pas and Throttle cable for the function
6 km / h? (but in this case I would like throttle too with 100% chance).
Mine (it seems) has 2 sockets where it is possible
connect the Throttle,: the 5 pin (with cruise) and the 3 pin (right photo),
now I have connected to the 5 pin (photo on the left), but I have a void
about 15 degrees before departure,
what setting should I change?
Also to avoid abrupt departures, for
not to break the gears?
I would appreciate any advice on various settings of various kinds, thanks.
Note: Now the 12 fet EB3 IRFB4110 controller sensored em3ev is programmed for 12a 30a at 48v.
The C.A. I prefer not to have it.
If can program the pas directly without a display,
then the display i will not connect.
As I bought the control, I did not buy from them
pas and the display (I already had it), it's hard to make me
give precise details, the seller seems to me to say that the display pas connects as with C.a.
Sorry for the translation.
to the control unit (true?) (to the 6-wire connector of the AC (or display) of the control unit,
(is in the middle see photo):
1 Battery Voltage Vcc-L (red
(I think it's battery indicator, my 48v., and I do not need to use it)
2 GND / Shunt + ve (black)
3 Shunt -ve / Shunt -ve (blue)
4 Shunt + ve / Shunt + ve (white)
5 Speed Signal / HE (yellow)
6 Throttle signal / SLA. (green)
So: where do I connect pas directly without the diplay and c.a.?
My pas is different, I have read that not all pas are compatible
with the control units, but I want to try,
but the display looks the same.
If the pas is connected directly, programmed to
30% does not work,
I should also connect the display, so: how do I connect display and pas?
Or display and pas and Throttle cable for the function
6 km / h? (but in this case I would like throttle too with 100% chance).
Mine (it seems) has 2 sockets where it is possible
connect the Throttle,: the 5 pin (with cruise) and the 3 pin (right photo),
now I have connected to the 5 pin (photo on the left), but I have a void
about 15 degrees before departure,
what setting should I change?
Also to avoid abrupt departures, for
not to break the gears?
I would appreciate any advice on various settings of various kinds, thanks.
Note: Now the 12 fet EB3 IRFB4110 controller sensored em3ev is programmed for 12a 30a at 48v.
The C.A. I prefer not to have it.
If can program the pas directly without a display,
then the display i will not connect.
As I bought the control, I did not buy from them
pas and the display (I already had it), it's hard to make me
give precise details, the seller seems to me to say that the display pas connects as with C.a.
Sorry for the translation.