Search results

Date Relevance Most replies

  1. K

    E-Street Machine 20kW

    i recently opened mine with a 3 jaw puller,if your 3 jaw puller is held together by two rectangle looking spacer with holes drilled on it for the bolt to go in,you can unloosen it and re extend the feet of the jaw puller
  2. K

    wiring issues to a Kelly controller with throttle

    My Kelly controller has been wire to a twist throttle but it runs on a very low rpm but when it twist it, it runs faster, what could be the issue, do I need to use a resistor from the throttle to the controller or any suggestion,I have a red,blue,green and yellow wire on my throttle and i also...
  3. K

    Kelly controller will not power on

    i have a kelly controller and i have tried different combination on my throttle wires but the red led light flashes 3 times stops and 3 times again meaning incorrect nor bad throttle and also the motor cogs or stutter without applying the throttle and it also draw alot of amps up to 180amps ,i...
  4. K

    Kelly controller will not power on

    what voltage should i use to power it and what is the wire label because i have the J1 and J2 wire connector ?
  5. K

    Kelly controller will not power on

    i have a KHB12401 kelly controller and it is connected through a shunt then to the cycle analyst,whenever i connect a battery to the B+ and B- it doesn't show any light,i used the pwr and rtn wire to configure it ,but it flashes red light with some error code,does anyone have an experience...
  6. K

    Current draw from cycle analyst without applied throttle

    there is nothing connected to the cycle analyst ,even when controller is disconnected it still draws current and i tried a different controller but still the same results
  7. K

    Current draw from cycle analyst without applied throttle

    hey guys ,my cycle analyst draws about 4.7 - 5 amps when turned on with the key switch without using the throttle and motor disconnected,has anyone ever experienced this problem before ,any suggestion or help is appreciated ?
  8. K

    PLACE TO LACE A HUB MOTOR IN USA ?

    Hey guys,do you know of any place in usa that make custom spokes,lace hub motor and sells rims for ebike,i have a 8kw hub motor that i'm trying to lace but voltriders said they are going out of business and so i don't know anywhere else to lace my hub motor ?
  9. K

    420A 24S ESC by aliens

    Yeah i suggest they try the new esc and i believe it won't fail like the older version did,wider heatsink for heat dissipation but the esc doesn't even get hot at all,i'm looking forward to another test or else i will do one when i get my bike together and running :twisted:
  10. K

    420A 24S ESC by aliens

    Here are my youtube videos of riding with the alien power system esc i've been using it for months now no problem http://www.youtube.com/watch?v=fSYDlOTbfk0 http://www.youtube.com/watch?v=vKlBpQIUZj0
  11. K

    420A 24S ESC by aliens

    Nice test luke,i have to confess that when i used the older version of the alien power system controller it failed me and this was tested with my 6kw hub motor but when i told bruno about it he replaced it immediately with the newer version and since then i have never had any problem with my...
  12. K

    Deley when letting off trottle ?

    The delay experienced when you use the gas is due to the fact that you have a sensorless controller,there are no hall sensors so the motor receiving the current will act in a different manner because there are no poles count for motion,i experience that with my sensorless controller on my ebike...
  13. K

    The Road to Higher HP 100-200-500+ HP

    check out this thread and contact the supplier of this motor and controller for you need because it might be useful http://endless-sphere.com/forums/viewtopic.php?f=30&t=50929&p=761180&hilit=liquid+cooling#p761180
  14. K

    Greyp eBikes

    As for me guys i don't care about the law placed on electric bikes that's why i installed a police detector on my bike to slow down when i hear a beeping sound on my device informing me there is a police around ,other than that i don't ride slow on the road :twisted:
  15. K

    CROMOTOR/CONTROLLER--QUESTION.

    30s sounds like alot of battery but if you decide to run a 24s lipo battery,you can contact bruno for an alien power system controller about 100volts 450amps if your motor can handle it or reduce the current using a cycle anaylst,i have one and it works great for me ,you can choose between a...
  16. K

    Alien Power System Calibration sequence??

    i have never calibrated mine using any other form rather than my computer software and alien programming box,if you still can get it to work try downloading the alien power system software on your computer or buy a programming box,you can also contact bruno concerning your problem
  17. K

    Colossus alternative (120100 Outrunner)

    i plan on making a mid drive electric bike with this or an ultralight aircraft,i have spoken to bruno about it
  18. K

    Greyp eBikes

    i don't know so much about this bike ,i was watching an online video and came across it,i still don't understand why it has 12kw with such a low speed ,but i think the speed setting could be changed because i can see a large kelly controller in there,also price range and features in comparison...
  19. K

    Greyp eBikes

    http://www.greyp-bikes.com/ , http://www.youtube.com/watch?v=A65dt-zLdSw A65dt-zLdSw mod edit (bigM) fixed your links.
  20. K

    Affordable Reliable Hydralic Disc brakes pairs

    you can check ebay for brakes and you could get a very reasonable price on them, something like this http://www.ebay.com/itm/HAYES-STROKER-TRAIL-DISC-BRAKE-KIT-FRONT-WHITE-900mm-HOSE-/281123975197?pt=US_Brakes&hash=item41744b701d...
  21. K

    420A 24S ESC by aliens

    it is a bicycle front brake 203mm (avid)
  22. K

    420A 24S ESC by aliens

    i have done 72mph so far on this bad boy
  23. K

    High current motor needed capable of 400amps continuous

    Hey guys is there any hub motor out there that can can handle 300-400amps on 100volts continuous or at least one hour without heating problems within the the dropout range of 200mm,i'm considering going a 70mile of range journey on a highway with a speed of 75-85mph continuous without any...
  24. K

    420A 24S ESC by aliens

    i have 6 10awg wire going through my motor axle,2 for each of the phases so my phase wire never melted or did i have any issue with the phase wires :D
  25. K

    420A 24S ESC by aliens

    Zombie be careful with your test because that controller is capable and strong enough to fry/toast your windings in your cromotor :twisted:
Back
Top