KT-LCD8H settings

T

timirwin

10 mW
Joined
Dec 14, 2023
Messages
24
Location
Bognor Regis
Hi I have a KT-LCD8H and I have changed the settings but now I can't see what speed im doing because it just stays on zero,
How do you change the settings to see what speed you are doing?
 
I once installed an KT-LCD8S with a G311 Bafang motor for a friend:

Check my settings:

P1: 176. I obtained this by multiplying 11 by 16, where in this case, 11 is the gear ratio, and 16 is the number of magnets on the G311 motor.

P2: Wheel generated 6 pulse signal by a revolution.

C1: 5. You can also test where the PAS sensor is mounted, on the left or right pedal.

C10: If you want to to automatically restore factory settings.

na.JPG
 
B_c said:
I once installed an KT-LCD8S with a G311 Bafang motor for a friend:

Check my settings:

P1: 176. I obtained this by multiplying 11 by 16, where in this case, 11 is the gear ratio, and 16 is the number of magnets on the G311 motor.

P2: Wheel generated 6 pulse signal by a revolution.

C1: 5. You can also test where the PAS sensor is mounted, on the left or right pedal.

C10: If you want to to automatically restore factory settings.

View attachment 344422
Click to expand...
Thank you for your reply my wheel size is 700c but I don't have PAS sensor mounted.
 
Then, you only have throttle control. If you can, please show with a picture how your settings look.

Or, alternatively, you can enter C10 and restore factory settings.
 
B_c said:
Then, you only have throttle control. If you can, please show with a picture how your settings look.

Or, alternatively, you can enter C10 and restore factory settings.
Click to expand...
My kit is a 48V 1500w brushless motor with a 48V 17AH battery.
 
Do you remember what you changed?
Or with which settings you tested, or what you wanted to achieve?

Once something funny happened to me, and I was checking everything like you are now, only to realize I had the assist level set to 0.
 
Last edited:
The only thing I remember changing was LIM, DIM and UNT and I think P1 and I wanted to change the the setting to enable the thumb throttle.
 
I have a 48V 1500W REAR WHEEL CONVERSION KIT with a 36V controller and a 48V 17AH Lithium Hailong Li-ion Battery fitted on a trek dual sport 2 can someone tell me what the best settings for the LCD8H screen are too get the highest speed and to make the battery last longer before each charge.
I have tried all the above but have not had any luck.
These are my current settings.

Moderator edit: removed "shouting" of huge bold font size. Please only post normal text size, using such things to highlight specific things like section headers, etc. Making your entire post huge just makes it difficult for anyone to read, and less likely for them to be able to help you.
 
Last edited by a moderator:
YouTube is your friend.

 
If what you wrote above is true...I think it's not advisable to use your 36-volt controller with a 48-volt battery.
In that case, parameter P5 is incorrect.
 
Try to change P3 to 0. When set to 1, the PAS level limits speed. Regardless of if the PAS is installed of not.

Here are my settings for my Shengyi 1000w geared rear hub motor.

IMG_3519.jpeg
 
Last edited:
Change C5 to 10 as docw009 said because, as it is now at 5, it means 1/3 less current from the controller.
 
You must log in or register to reply here.

Similar threads

A
G310 speed/thermistor & KT Controller/Display
Replies
3
Views
818
adcockj
A
S
How do you use Grins new v6 Z9 BaseRunner with a 3rd party display?
Replies
6
Views
1,199
Aeron
Aeron
J
Jerky motor
Replies
20
Views
1,377
neptronix
neptronix
H
MAX speed of 30mph on my DIY E-Bike kit. 3000w, 72v battery, 30amp controller. What am I doing wrong?
Replies
10
Views
5,577
2old
2
K
  • Question
No power level selection SW900: Always at max power regardless of any PAS or other settings.
Replies
5
Views
102
amberwolf
amberwolf
Back
Top