Powervelocity.com
100 kW
Probably the most advanced FOC controller on the market.
Fully isolated design for safety and reliability. Built-in hardware protections.
It's designed from the ground up to run high voltage and currents without blowing up or spewing plasma.
Unique built-in features:
- on-board contactor for soft turn-on to prevent arcing when connecting the battery and full disconnect for fire safety;
- Simple to use PV-NextGen app, and easy to configure from an iOS and Android phone;
- boost charging from any DC source via motor coils - up to 144v regulated charging from 15v and above - can be charged direct from solar panels:
More Details
- Support up to 32S battery packs (140v). Power component rated up to 150v. 200v version is coming.
- 300A max battery peak discharge (conservative);
- Mosfets rated up to support 850A peak phase current. Tested up to 400A so far;
- 24F SMT/leadless mosfets mounted on a metal core substrate PCB with direct thermal interface to the heatsink enclosure, best cooling possible in fanless/non-liquid cooled designs;
- Control circuits are fully isolated from high voltage for best transient immunity;
- Precise and linear torque control up to 100% of throttle due to three phase current measurement architecture;
- Best in class components used for critical systems such as the gate drivers and voltage sensors;
- Support of a wide variety of motors including low inductance, IPM, DC, pretty much anything that is considered a motor;
- One button motor detection (from the app or display);
- Supports sensored, sensorless, encoder, etc. all modes of operation are supported;
- Max Torque Per Amp (MTPA) and field weakening supported;
- up to 150,000 eRPM;
- Compact and light design ( below 1kg, ~2lbs), probably, smaller and lighter than anything available today in this power category;
- Current throttle control, variable regen;
- Mappable throttle voltages for precise control (dead band elimination);
- Temperature monitoring for controller and input for motor temperature, NTC, PTC probes supported;
- Configurable power limits with dynamic/soft power rollbacks based on state of charge, temperatures, RPM;
- Protections against overvoltage, overcurrent, overspin, overtemperature, and many other overs;
- Over-the-air (OTA) updates via WiFi;
- iOS and Android app for easy one-button motor detection; configuration and HUD via Bluetooth;
- Online data logging (can be viewed in the phone app or via a web browser).
- Boost charging mode via motor coils from any DC source with voltage lower than your target battery voltage (current and voltage settable in the app);
- CAN comm supported;
- multi-motor configuration supported, including traction control;
- Built-in contactor (soft turn-on and full disconnect)
Price and options
1. Controller + app: $799(140v version)
2. Controller + GPS/Remote connectivity package (included/free 3 years data): $899
Note: Remote connectivity package supports coverage in ~70 countries. Please check before buying if your country is on the list.
Fully isolated design for safety and reliability. Built-in hardware protections.
It's designed from the ground up to run high voltage and currents without blowing up or spewing plasma.
Unique built-in features:
- on-board contactor for soft turn-on to prevent arcing when connecting the battery and full disconnect for fire safety;
- Simple to use PV-NextGen app, and easy to configure from an iOS and Android phone;
- boost charging from any DC source via motor coils - up to 144v regulated charging from 15v and above - can be charged direct from solar panels:
More Details
- Support up to 32S battery packs (140v). Power component rated up to 150v. 200v version is coming.
- 300A max battery peak discharge (conservative);
- Mosfets rated up to support 850A peak phase current. Tested up to 400A so far;
- 24F SMT/leadless mosfets mounted on a metal core substrate PCB with direct thermal interface to the heatsink enclosure, best cooling possible in fanless/non-liquid cooled designs;
- Control circuits are fully isolated from high voltage for best transient immunity;
- Precise and linear torque control up to 100% of throttle due to three phase current measurement architecture;
- Best in class components used for critical systems such as the gate drivers and voltage sensors;
- Support of a wide variety of motors including low inductance, IPM, DC, pretty much anything that is considered a motor;
- One button motor detection (from the app or display);
- Supports sensored, sensorless, encoder, etc. all modes of operation are supported;
- Max Torque Per Amp (MTPA) and field weakening supported;
- up to 150,000 eRPM;
- Compact and light design ( below 1kg, ~2lbs), probably, smaller and lighter than anything available today in this power category;
- Current throttle control, variable regen;
- Mappable throttle voltages for precise control (dead band elimination);
- Temperature monitoring for controller and input for motor temperature, NTC, PTC probes supported;
- Configurable power limits with dynamic/soft power rollbacks based on state of charge, temperatures, RPM;
- Protections against overvoltage, overcurrent, overspin, overtemperature, and many other overs;
- Over-the-air (OTA) updates via WiFi;
- iOS and Android app for easy one-button motor detection; configuration and HUD via Bluetooth;
- Online data logging (can be viewed in the phone app or via a web browser).
- Boost charging mode via motor coils from any DC source with voltage lower than your target battery voltage (current and voltage settable in the app);
- CAN comm supported;
- multi-motor configuration supported, including traction control;
- Built-in contactor (soft turn-on and full disconnect)
Price and options
1. Controller + app: $799(140v version)
2. Controller + GPS/Remote connectivity package (included/free 3 years data): $899
Note: Remote connectivity package supports coverage in ~70 countries. Please check before buying if your country is on the list.
Last edited: