DotScott
1 W
- Joined
- Feb 6, 2016
- Messages
- 52
Putting my new build together but so far I've encountered 2 problems...
๐ ๐ฌ ๐ฆ๐๐ง๐จ๐ฃ:
๐ ๐ผ๐๐ผ๐ฟ: QS205 50H V3
๐๐ผ๐ป๐๐ฟ๐ผ๐น๐น๐ฒ๐ฟ: Sabvoton SVMC 96120
๐๐ฎ๐๐๐ฒ๐ฟ๐ has a top charge of 97.7v and a low cut off of 70v, capable of 80 amps continuous output.
๐ญ. ๐ถ๐ณ ๐ ๐ฒ๐๐ฒ๐ป ๐๐๐ฟ๐ป ๐๐ต๐ฒ ๐๐ต๐ฟ๐ผ๐๐๐น๐ฒ ๐ฒ๐๐ฒ๐ป ~๐ญ/๐ญ๐ฌ๐๐ต ๐ผ๐ณ ๐๐ต๐ฒ ๐๐ฎ๐, ๐ถ๐ ๐ท๐๐๐ ๐ด๐ผ๐ฒ๐ ๐ณ๐๐น๐น ๐ฏ๐น๐ฎ๐๐... it's like it's 0 or 100 and nothing in between. My throttle shows the voltage range is from 1.17v to 5v as I twist it to 100% but the motor just goes full blast as soon as the throttle is even 0.1v above the low voltage - 1.17v (it seems). Currently have mid voltage set to 2.5v. I tried setting my throttle mid current to 50 (phase amps) for testing but... for some reason it resets to 0.02 A every time I twist the throttle or go to a different tab and then back...? Anyone know what I'm doing wrong here?
๐ฎ. ๐ ๐ ๐ค๐ฆ๐ฎ๐ฌ๐ฑ ๐ถ๐ ๐น๐ถ๐ธ๐ฒ... ๐ฆ๐จ๐ฃ๐๐ฅ ๐น๐ผ๐๐ฑ compared to every other motor I've had (on a sinewave controller). The noise level is about equivalent to a table or circular saw (see video in link below). When I spin the motor by hand, it's very clunky and almost sounds like something is scraping. Something I've never heard in any of my other hub motors. Is it normal for the QS205 to be this loud?
Link to video and settings photos:
https://drive.google.com/drive/folders/1okClsmJCk3Mo6cDQU19e-KE_a6_rYn5w?usp=sharing
๐ ๐ฌ ๐ฆ๐๐ง๐จ๐ฃ:
๐ ๐ผ๐๐ผ๐ฟ: QS205 50H V3
๐๐ผ๐ป๐๐ฟ๐ผ๐น๐น๐ฒ๐ฟ: Sabvoton SVMC 96120
๐๐ฎ๐๐๐ฒ๐ฟ๐ has a top charge of 97.7v and a low cut off of 70v, capable of 80 amps continuous output.
๐ญ. ๐ถ๐ณ ๐ ๐ฒ๐๐ฒ๐ป ๐๐๐ฟ๐ป ๐๐ต๐ฒ ๐๐ต๐ฟ๐ผ๐๐๐น๐ฒ ๐ฒ๐๐ฒ๐ป ~๐ญ/๐ญ๐ฌ๐๐ต ๐ผ๐ณ ๐๐ต๐ฒ ๐๐ฎ๐, ๐ถ๐ ๐ท๐๐๐ ๐ด๐ผ๐ฒ๐ ๐ณ๐๐น๐น ๐ฏ๐น๐ฎ๐๐... it's like it's 0 or 100 and nothing in between. My throttle shows the voltage range is from 1.17v to 5v as I twist it to 100% but the motor just goes full blast as soon as the throttle is even 0.1v above the low voltage - 1.17v (it seems). Currently have mid voltage set to 2.5v. I tried setting my throttle mid current to 50 (phase amps) for testing but... for some reason it resets to 0.02 A every time I twist the throttle or go to a different tab and then back...? Anyone know what I'm doing wrong here?
๐ฎ. ๐ ๐ ๐ค๐ฆ๐ฎ๐ฌ๐ฑ ๐ถ๐ ๐น๐ถ๐ธ๐ฒ... ๐ฆ๐จ๐ฃ๐๐ฅ ๐น๐ผ๐๐ฑ compared to every other motor I've had (on a sinewave controller). The noise level is about equivalent to a table or circular saw (see video in link below). When I spin the motor by hand, it's very clunky and almost sounds like something is scraping. Something I've never heard in any of my other hub motors. Is it normal for the QS205 to be this loud?
Link to video and settings photos:
https://drive.google.com/drive/folders/1okClsmJCk3Mo6cDQU19e-KE_a6_rYn5w?usp=sharing