Recent content by stefan010

You guys where right again, the connector had some loose wires/ bad connectioins. I contacted CA if he had spare part for the pushbutton. Thanks you all for the great answers !

Well i figure out the problem is within the buttons , i unplugged the button and the problem. But now i have also other the display keeps saying i draw like -1000W or -15Amps , anyone has encountered that problem before ? I hope CA can provide me spare for the buttons or i have figure out...

thnx for the advice ! I will try it 2morrow.

Hi all, I recently have some problems with my cycle analyst. It keep popping/jumping the display automaticly in all kind of modes and mostly it end ups in the setting mode ( Its like if someone pressing the buttons continiously on the analyst). Its very annoying and almost unable to bike...

Hey thn the tips so far . I was on a short vacation so i couldt go on with it. So 2night i had some freetime i managed to unscrew , the screws ( the cut in the screws and bigscrewdriver did the job) I only still cant rotor out , any one of you have some advice to take out the rotor. I only...

Yes is still the guessing phase , but I did the following : 1 : Unplugged the connector 2 : Try spin wheel no effect still gives friction 3 : put 2 wires together L1-L2 , L2-L3 , L3-L1 all these this combinations gives abit more friction then step 2 4: Put all wires together this gives...

Thnx for the tip Guys ! The wheel is now +3 years old. and i think put 10.000km on it. I think indeed there maybe is an internal short , if that could be possible. But know i have to find out the internal short , any suggestion on that. I already figure out opening the front is very hard...

hey i dont know if there is shorted phase , if there was shorted phase the motor wouldnt work anymore right ? How do i check if there is a phase shorted Bearing replacment would be hard i think especialy to get the wheel open :(

Dear Ebikers. Recently my Crystalite HS3540 motor has a problem , it gives pretty much friction on the shaft. When there is enough power aviable its no problem , but is drains batt pretty fast and also the speed is not optimal because of the friction. But when no power its very hard , to...

Being using HK lipo for more then 3 years now ! with very different experiences . I had build 2 packs first was a 6s 6*5ah and the moment i have a 6s 3*10ah. Oke first the pro's 1: The price , i think their is no better price then aviable for a 72V 10ah that hobbyking offers...

Ty you for advice en response . My CA.2.2 is not a stand alone version its directly connected to the lyen controller. I think the problem is in the spoke or in the sensor, the sensor picks something up and gives me al the weird speeds and therefore is cut of the power. At the moment i...

My cycle analyst v2.2. When cycle analyst (v2.2) is plugged it sometimes gives me somekind of speed error. When i pull the throtle the speedcounter on the display gives me an error and says iam over 200kph or other weird speeds. There fore the bike is not giving me any power . because the...

yep iam getting 75V on the output , (is configured for 18s) wich component is the voltage regulator ? I checked the 12v volt for the fan , and there i found a problem . When i take as a default ' - ' the blue output wire and i measure the '+' of the fan i see 12V , so why the fan dont start...

Iam from holland. I have pulled the plate of , i can take picture , but tthere doesnt seem anything unusual on it . The weird thing is , that the charger gives an output of 75V but there wont flow any current It wont charge when my battery is on it. the fan also dont start

the led sheens bright when i put my battery on it , and it also when its connnect to the socket 230VAC . No green led Only led 1 is red Led 2 gives no color at all ( red or green)