Golden2000
100 mW
- Joined
- Nov 29, 2022
- Messages
- 38
Adding throttle to a PAS bike for this controller
- Thread starter Golden2000
- Start date
lol that was the whole post, just a picture?
It's 100% worth the gamble to simply buy a KT display and controller for around $100 USD total, that already comes with PAS and throttle wires. Most PAS sensors and almost all throttles out there are compatible with KT stuff. As long as the motor is standard 9-pin, everything else 'should' work. If it doesn't, you have 30 days to return them with Amazon Prime. Just don't soldier the wires or do other irreparable mods.
It's 100% worth the gamble to simply buy a KT display and controller for around $100 USD total, that already comes with PAS and throttle wires. Most PAS sensors and almost all throttles out there are compatible with KT stuff. As long as the motor is standard 9-pin, everything else 'should' work. If it doesn't, you have 30 days to return them with Amazon Prime. Just don't soldier the wires or do other irreparable mods.
Golden2000
100 mW
- Joined
- Nov 29, 2022
- Messages
- 38
I have already this ebike controller… I don’t need the lcd just i want to wire throttle instead PAS but I don’t know how i wire it to run the wheels
Golden2000
100 mW
- Joined
- Nov 29, 2022
- Messages
- 38
Instead you post helpless reply ask wht i can help you !!! I post the controller name and all its pins I don’t know what you need else
AGS
1 kW
Throttle +5v = SP5V
Throttle 0v = SPGND
Throttle signal = SP
SP is far left in your photo and SP5V & SPGND are bottom right near where the the model number Is printed. The wires are already soldered into the pcb, so you just need to identify the 3 wires from the board and connect up your throttle.
These wires are probably red = +5v, black = 0v and green/yellow = signal. But don’t be concerned if you find the colours are different.
Throttle 0v = SPGND
Throttle signal = SP
SP is far left in your photo and SP5V & SPGND are bottom right near where the the model number Is printed. The wires are already soldered into the pcb, so you just need to identify the 3 wires from the board and connect up your throttle.
These wires are probably red = +5v, black = 0v and green/yellow = signal. But don’t be concerned if you find the colours are different.
Last edited:
Golden2000
100 mW
- Joined
- Nov 29, 2022
- Messages
- 38
This is another type of controller without sp …
AGS
1 kW
You may find the SP connection is printed on the other side of the circuit board on the LSW6G controller.
Last edited:
Golden2000
100 mW
- Joined
- Nov 29, 2022
- Messages
- 38
Adding throttle to a PAS bike
Hi there first time posting here. Sorry about my english but it is not my native language. Im trying to add a throttle in a bike i own. It has only PAS and a led panel where u can choose the PAS level, on/off button and a 6km/h button. Controller: Wiring: It has these wires + the power /...
endless-sphere.com
AGS
1 kW
What did you wire the other two wires to from the throttle?
HV5V and HVGND?
HV5V and HVGND?
Golden2000
100 mW
- Joined
- Nov 29, 2022
- Messages
- 38
no my friend i think HV5V and HVGND its for hall sensor …
If you would post the requested pic, it would help. You could also search "add throttle to lishui".
Tried to help you buddy, but you ignored my request for the pic.
Golden2000
100 mW
- Joined
- Nov 29, 2022
- Messages
- 38
Golden2000
100 mW
- Joined
- Nov 29, 2022
- Messages
- 38
As AGS stated, look for the SP connection on the board, if the controller supports throttle. I don't see one, but it could be under that big cap or in a corner of the board that you can't see in the photo.
Golden2000
100 mW
- Joined
- Nov 29, 2022
- Messages
- 38
I didn’t find SP pin on this board !!!
