Final shopping list. With pictures.
- Thread starter zjhost
- Start date
zjhost
100 mW
Punx0r said:
It would be but they're not in stock right now. I am going to ask them some more. I'm wondering where the extra 14 dollars go to..
zjhost
100 mW
A little update, I ordered the controller and everything from hobbyking for charging. Except the parallel charging board. I ordered that one from epbuddy ( I'll update my first post on the shopping list.)
I didn't order the batteries yet because I will order them from the euro warehouse and with faster shipping I would have the lipo's just laying around here, without lipo bag ((which I ordered also) see first post))
I ordered the controller along with a hd camcorder so I will probably make a youtube series or something like that, I'll keep you up to date
.
I will order the hub motor and battery when everything is at my house. Shipping would only take 2-6 days.
I didn't order the batteries yet because I will order them from the euro warehouse and with faster shipping I would have the lipo's just laying around here, without lipo bag ((which I ordered also) see first post))
I ordered the controller along with a hd camcorder so I will probably make a youtube series or something like that, I'll keep you up to date
.I will order the hub motor and battery when everything is at my house. Shipping would only take 2-6 days.
zjhost
100 mW
Expected cost are 900 euro. My moped is still for sale it should bring me at least 900 euro.
zjhost
100 mW
Shopping list in pictures
My apologies for the shaky/bad quality of the photo's I took them with my phone. The camera I ordered from dhgate didn't arrive yet, neither did the controller.
This is the package I recieved already unboxed
picture hosting
This is the paraboard from ebuddy, this was in a serperate package of course.
photo upload
This is the battery medic from hobby king, a little smaller than I expected.
upload photo
Battery monitor.
upload photo
JST-XH connector extension wires, better quality than I expected.
free image hosting
20cm like they said on the HB site.
upload pictures
Bullet connectors. Good quality.
free image hosting
The Turnigy charger, it does work. Have not tested it on batteries yet. And it automaticly detected that the power supply was LOW, no big deal, I can keep the amps down. The stain you see on the screen is the light.
free picture hosting
This is the power supply, works well, makes a lot of noise though. Turns out I could have bought a 350w power supply second hand pretty cheap. If it's necessary I'll do that later on.
free image hosting
And then there is the TURNIGY 10AWG wire, I measured the width which was 5mm.
On the paraboard the width of the wire is also 5mm but that wire is 12AWG.
The wire that comes out of the TURNIGY charger (12AWG) is 4mm.
just something I noticed maybe it's nothing. Couldn't really measure precise. I'll do that later.
I'm going to have to buy an external discbrake adapter for the prokit, they sell those at devi-motion too.
When I buy the batteries and the prokit it will only take 2 days to arrive. I want to sell my moped first though.
So, what do you think?
My apologies for the shaky/bad quality of the photo's I took them with my phone. The camera I ordered from dhgate didn't arrive yet, neither did the controller.
This is the package I recieved already unboxed
picture hosting
This is the paraboard from ebuddy, this was in a serperate package of course.
photo upload
This is the battery medic from hobby king, a little smaller than I expected.
upload photo
Battery monitor.
upload photo
JST-XH connector extension wires, better quality than I expected.
free image hosting
20cm like they said on the HB site.
upload pictures
Bullet connectors. Good quality.
free image hosting
The Turnigy charger, it does work. Have not tested it on batteries yet. And it automaticly detected that the power supply was LOW, no big deal, I can keep the amps down. The stain you see on the screen is the light.
free picture hosting
This is the power supply, works well, makes a lot of noise though. Turns out I could have bought a 350w power supply second hand pretty cheap. If it's necessary I'll do that later on.
free image hosting
And then there is the TURNIGY 10AWG wire, I measured the width which was 5mm.
On the paraboard the width of the wire is also 5mm but that wire is 12AWG.
The wire that comes out of the TURNIGY charger (12AWG) is 4mm.
just something I noticed maybe it's nothing. Couldn't really measure precise. I'll do that later.
I'm going to have to buy an external discbrake adapter for the prokit, they sell those at devi-motion too.
When I buy the batteries and the prokit it will only take 2 days to arrive. I want to sell my moped first though.
So, what do you think?
zjhost
100 mW
Caliban said:
Ok thanks I'll keep that in mind
zjhost
100 mW
Hi all, it has been a long time since i posted something. I have been on and off my project but 2 weeks ago I received the Prokit 901 and today I got my batteries.
The frame is still the way it was. It needs to be painted but I'm not sure if it's smart to paint when it's freezing, probably not.
The batteries( Turnigy 5000mAh 4S1P 14.8v 20C hardcase pack )I got today are looking awesome. I measured the voltage of all 6 batteries and they were all about 3.6 V. The difference in cells was never more than 0.06 V. I'm happy with that.
I was surprised by the prokit 901 it feels really decent. The disk brake adaptor that I had to buy separately didn't fit my disk. My colleague cnc machined the new holes. This is how it looks now:
Unboxing batteries:
The frame is still the way it was. It needs to be painted but I'm not sure if it's smart to paint when it's freezing, probably not.
The batteries( Turnigy 5000mAh 4S1P 14.8v 20C hardcase pack )I got today are looking awesome. I measured the voltage of all 6 batteries and they were all about 3.6 V. The difference in cells was never more than 0.06 V. I'm happy with that.
I was surprised by the prokit 901 it feels really decent. The disk brake adaptor that I had to buy separately didn't fit my disk. My colleague cnc machined the new holes. This is how it looks now:
Unboxing batteries:
Ykick
1 GW
Nice, fresh Lipoly!
zjhost
100 mW
I just hooked up the batteries and did a quick test and it works
the batteries are actually all about 3.85V. Except for one battery, one cell has a voltage of 3.79.
the batteries are actually all about 3.85V. Except for one battery, one cell has a voltage of 3.79.
