Waynemarlow
10 kW
Has anyone found a reliable supplier of the M500 / M600 engines to the UK, quite happy to get direct from China but just need a used supplier that people have gotten on with.
Thanks
Thanks
Fraben said:![]()
![]()
Very cool yeah.
How can you make a can analyzer, or where can we buy it?
Waynemarlow said:The biggy would be can you change the assist levels.
Waynemarlow said:Thanks,
My packs are all 58.6v fully charged, anyone tried it on this level ?
Animalector said:I've had Error30 a couple of times, it locks up the display. I remove the battery and reinsert and then it's fine again.
Interestingly, both times was while watching the 'power' option on the display. when the display is sitting on 'trip' it seems to be ok.
I'm thinking firmware to do with the CANBus comms.... are your firmware versions the same (you can check in the display menus I think)
Error 30 is defined as "Communications Error"
Andy
There is a small crowd of us on Luna's forums following your progressdentata said:CiDi said:I enclose the firmware for M600 43V from August 2020 and the firmware 48V from November 2019.
I think the 43V is better than the 48V even in a 48V system.
Has anyone successfully flashed a controller originally with 14.5 to 14.6? I just tried flashing with this 14.6 firmware and the motor would not turn on until it was flashed back to the original.
dentata said:CiDi said:I enclose the firmware for M600 43V from August 2020 and the firmware 48V from November 2019.
I think the 43V is better than the 48V even in a 48V system.
Has anyone successfully flashed a controller originally with 14.5 to 14.6? I just tried flashing with this 14.6 firmware and the motor would not turn on until it was flashed back to the original.
Controller
Software CRX10NC4818i132014.5
Hardware CR X10N.500.FC 3.2
Torque sensor
Software SRPA212CF10101.0
Hardware SR PA21232ST.C 1.0
eskachig said:dentata said:CiDi said:I enclose the firmware for M600 43V from August 2020 and the firmware 48V from November 2019.
I think the 43V is better than the 48V even in a 48V system.
Has anyone successfully flashed a controller originally with 14.5 to 14.6? I just tried flashing with this 14.6 firmware and the motor would not turn on until it was flashed back to the original.
I asked Bafang for the latest firmware for our motor, and this is what they got back to me with. Not even sure how to read that version, but there it is. If you still have the tool and are interested, maybe you can give it a shot. I posted this in the Luna forum thread too.
https://mega.nz/file/grYnCKKa#ncPZSp...qbF8j5dR3mxWKo
The version and date are rather different than what we've been seeing, I'm not sure what to make of it.
CRX10NC4818i132046.6-28-2230-20200824-3.bin
It seems to match the motor format and voltage though. This is the info I provided to them:
Controller
Software CRX10NC4818i132014.5
Hardware CR X10N.500.FC 3.2
Torque sensor
Software SRPA212CF10101.0
Hardware SR PA21232ST.C 1.0
Holy crap those wankers. (edit: turns out I'm the wanker)CiDi said:The link doesn't work, can you post the file directly? Just rename it ".txt"
eskachig said:Holy crap those wankers. (edit: turns out I'm the wanker)CiDi said:The link doesn't work, can you post the file directly? Just rename it ".txt"
I'm going to try again. I'm trying to avoid posting it as a txt, because something went wrong with the .bin files posted that way earlier - both Luna and a user here couldn't get them to work after that.
Link : https://mega.nz/file/grYnCKKa
Decryption key: ncPZSpme-XWPk30zGEajSUN_9FNcZqbF8j5dR3mxWKo
You can also PM me and I can email you the file. Or, does anyone else know a place that will host a .zip?
Edit: Ah, I see, somehow the link from earlier got shortened with an ellipsis in there. Should be https://mega.nz/file/grYnCKKa#ncPZSpme-XWPk30zGEajSUN_9FNcZqbF8j5dR3mxWKo (shows up with an ellipsis but should work now).