Rally
1 µW
Hello everyone! I'm looking to buy a votol em50sp to go with my current setup. I'm wondering if anyone can help me write the parimators for the program. I've already got the software and made a rough config file for when I get the controller in the mail here soon
.
My set up.
72v30ah lithium with a 50-60a bms.
yuanlang ykjg015 controller (no info on that online)
QS motors Qs205 50h v3 hub motor??
Or a qs motors 500w super torque (as per the emmo web site)
Someone told me that the emmo zone GTS 500w motor only contains 12 pole pairs if someone were to upgrade controller.( same motor I have as per the emmo web site.)
Chat gpt says I have the qs205 tho? I'm confused.
I just need help with the small stuff in the software to make sure I'm good to go for a first run.
Can anyone look over what I have so far and maybe guide me in the right direction with anything that needs changed?
Any and all help is appreciated greatly.
Included are pictures of the param that I attempted to make today with what I know about the controller (votol em50sp) and my setup. If any other info is needed please let me know!
Thank you all in advance
Rally
2023 emmo koogo
The emmo site says I have a qs super torque 500 watt motor. It says qs motors on one side. And this number on the other side EY0150BM72038 Chat gpt results says its a qs205 v3 50h hub motor???
So now I'm confused on how many pole pairs to input into the software. Included is picture of the numbers
P. S. My current setup. Speed 1. 32kph. Speed 2. 48kph. Speed 3. 60-63kph. With this new controller looking for more torque and top end. Keep my cruise control. And wire one of my 2 horn buttons in for the boost function down the road.
P.s.s. Info on the em50sp
Max power 3960W, 72v, Max DC current 55a, boost DC current. 60a, phase current 190a, mosfets 12 FET, matched motor rated pwr 800-2000w, max efficiency 92%
Im at a loss on what exactly to input. Like beside
the 3 speed, I don't know what to put the values at in the side bar beside my percentages I put down. Ahhhhhhhh help!!! . If possible step by step as per what the software is asking of me. I don't want to screw this up. Please help. If any more info is need and I have it I'll gladly input it.
Thank you again for reading this and your time
.
My set up.
72v30ah lithium with a 50-60a bms.
yuanlang ykjg015 controller (no info on that online)
QS motors Qs205 50h v3 hub motor??
Or a qs motors 500w super torque (as per the emmo web site)
Someone told me that the emmo zone GTS 500w motor only contains 12 pole pairs if someone were to upgrade controller.( same motor I have as per the emmo web site.)
Chat gpt says I have the qs205 tho? I'm confused.
I just need help with the small stuff in the software to make sure I'm good to go for a first run.
Can anyone look over what I have so far and maybe guide me in the right direction with anything that needs changed?
Any and all help is appreciated greatly.
Included are pictures of the param that I attempted to make today with what I know about the controller (votol em50sp) and my setup. If any other info is needed please let me know!
Thank you all in advance
Rally
2023 emmo koogo
The emmo site says I have a qs super torque 500 watt motor. It says qs motors on one side. And this number on the other side EY0150BM72038 Chat gpt results says its a qs205 v3 50h hub motor???
So now I'm confused on how many pole pairs to input into the software. Included is picture of the numbers
P. S. My current setup. Speed 1. 32kph. Speed 2. 48kph. Speed 3. 60-63kph. With this new controller looking for more torque and top end. Keep my cruise control. And wire one of my 2 horn buttons in for the boost function down the road.
P.s.s. Info on the em50sp
Max power 3960W, 72v, Max DC current 55a, boost DC current. 60a, phase current 190a, mosfets 12 FET, matched motor rated pwr 800-2000w, max efficiency 92%
Im at a loss on what exactly to input. Like beside
the 3 speed, I don't know what to put the values at in the side bar beside my percentages I put down. Ahhhhhhhh help!!! . If possible step by step as per what the software is asking of me. I don't want to screw this up. Please help. If any more info is need and I have it I'll gladly input it.
Thank you again for reading this and your time
Attachments
Last edited:
